Blue Rhino Crossfire GBT1508B Manuel Du Propriétaire page 13

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Recipes
BlueRhino.com/recipes
Troubleshooting
Problem
Burner will not light using ignitor
(if included)
Burner will not light with match
Sudden drop in gas flow or reduced flame height Out of gas
Irregular flame pattern – flame does not run the
full length of burner
Flame is yellow or orange
Flame goes out
Flare-up
Persistent grease fire
Flashback (fire in burner tube(s))
Inside of lid is peeling (like paint peeling)
Need help? 1.800.762.1142
Do not return to place of purchase.
Possible Cause
LP gas tank is low or empty
LP gas leak
Wires or electrode covered with cooking residue
Electrode and burners are wet
Electrode cracked or broken - sparks at crack
Wire loose or disconnected
Wire is shorting (sparking) between ignitor and electrode Replacement part(s) may be needed - contact Customer Care at 800.762.1142
Bad ignitor
No gas flow
LP gas tank is low or empty
LP gas leak
Coupling nut and regulator not fully connected
Obstruction of gas flow
Spider webs or insect nest in venturi
Burner ports clogged or blocked
Burner ports are clogged or blocked
New burner may have residual manufacturing oils
Spider webs or insect nest in burner/venturi tube
Food residue, grease, etc. on burners
Poor alignment of valve to burner/venturi tube
High or gusting winds
Low on LP gas
Overflow valve tripped
Grease buildup
Excess fat in meat
Excessive cooking temperature
Grease trapped by food buildup around burner system
Burner and/or burner tubes are blocked
Baked on grease buildup has turned to carbon and is
flaking off.
For more assistance, please visit us at BlueRhino.com or call 1.800.762.1142.
Replacement Parts
parts.BlueRhino.com
1.800.762.1142
Prevention/Cure
Replace LP gas tank
1.
Turn LP gas tank valve to " OFF"
2.
Wait 5 minutes for gas to clear
3.
Follow "Checking for Leaks" section
Clean wire and/or electrode with rubbing alcohol
Wipe dry with cloth
Replacement part(s) may be needed - contact Customer Care at 800.762.1142
Reconnect wire or replacement part(s) may be needed - contact Customer Care
at 800.762.1142
Replacement part(s) may be needed - contact Customer Care at 800.762.1142
Check if LP gas tank is empty
A. If empty, replace
B. If LP gas tank is not empty, refer to "Sudden drop in gas flow or reduced
flame height" below
Replace LP gas tank
1.
Turn LP gas tank valve to " OFF"
2.
Wait 5 minutes for gas to clear
3.
Follow "Checking for Leaks" section
Turning the coupling nut about one-half to three-quarters additional turn until
solid stop. Tighten by hand only-do NOT use tools
Clear burner/venturi tube
Clean burner/venturi tube
Clean burner ports
Replace LP gas tank
Clean burner ports
Operate grill for 15 minutes on (HIGH) with the lid closed
Clean burner/venturi tube
Clean burner
Ensure burner/venturi tube is properly engaged with valve
Do not use grill in high winds
Replace LP gas tank
Refer to "Sudden drop in gas flow or reduced flame height," above
Remove and clean all grill parts per "Cleaning and Care" section
Trim fat from meat before grilling
Adjust (lower) cooking temperature
1. Turn control knob to " OFF"
2. Leave lid in closed position and let fire burn out
3. After grill cools, remove and clean all grill parts per "Cleaning and Care"
section
Clean burner and/or burner/venturi tube
Clean all grill parts per "Cleaning and Care" section
13

Publicité

Table des Matières
loading

Table des Matières