Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Jack-IT
BikeWing not
included with
Bump-IT kit
Table of Contents
Introduction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Patent protected, trademarked, and produced by Let's Go Aero, Inc.
Corporate Office: 4474 Barnes Road, Colorado Springs, CO 80917 USA.
Made in Taiwan.
US Patent Numbers: 8,899,456, D717,716, D717,717, D684,917, D722,289,
patents pending.
lci1.com
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
574-537-8900
Bump-IT
Rack Adapter
Installation and Owner's Manual
(For Aftermarket Applications)
Bump-IT
Bicycle Rack
Adapter
Installation and
Owner's Manual
(For Aftermarket Applications)
Bump-IT Bicycle Rack Adapter Aftermarket Kit
Bump-IT Bicycle Rack Adapter Aftermarket Kit
Part #
Part # Description
Description
723359
Bump-IT
™
Introduction
™
The Bump-IT
accessory enables Jack-IT
owners to easily move their bicycle rack between their
1
travel trailer and tow vehicle.
The Bump-IT plugs into a tow vehicle's rear hitch receiver.
2
The product has a hitch adapter and will fit both 1.25" and
2
2" hitch receivers.
2
Once Bump-IT is secure on the tow vehicle, owners detach
2
the BikeWing assembly from Jack-IT and then attach and
2
secure it to the Bump-IT using the same NoMotion
3
that secured the BikeWing to the Jack-IT.
3
When it's time to leave the campsite, owners can reattach
3
the BikeWing to the Jack-IT and secure it with the
4
NoMotion pins.
4
4
The Bump-IT is for use only with the Jack-IT bicycle rack.
The NoMotion pins minimize wobble and the textured,
powder-coated finish resists scratching.
There is an 80-pound weight limit for cargo, and the overall
length is 22.5" with 17" of inside bicycle clearance.
The kit contains the Bump-IT accessory, one NoMotion hitch
pin, locking hairpin cotter pin, hex wrench, adjuster wrench,
aluminum adapter, socket head hex screw for the adapter
and washers. The patent number is US9,663,040B1.
1
CCD-0002228
Bicycle
™
™
accessory with mounting hardware
®
bicycle rack
™
pin
Rev:02.11.20
Publicité
Table des Matières
Sommaire des Matières pour Lippert Components Bump-IT
-
Page 1: Table Des Matières
......The Bump-IT is for use only with the Jack-IT bicycle rack. The NoMotion pins minimize wobble and the textured, powder-coated finish resists scratching. -
Page 2: Jack-It Installation Information
” adjuster wrench (Included with kit) • Socket wrench with ” socket (Optional) Installation NOTE: The triangular gusset on the end of the Bump-IT shank should face down, away from the bicycles. This orientation is important to provide additional strength to the Bump-It rack. -
Page 3: Attach To 1.25" Hitch Receiver
(For Aftermarket Applications) Attach to 1.25” Hitch Receiver Attach BikeWing to Bump-IT 1. Slide the shank of the Bump-It rack into the vehicle’s 1. Detach the base of the Jack-IT bicycle rack’s BikeWing hitch receiver and align the pin holes. -
Page 4: Securing Bicycles
5. Repeat steps 2-4 for a second bicycle on the other side of the bicycle rack. Mounting Clearance The Bump-IT is 22.5” long from front to end, and there is ≈ 17” approximately 17” of inside bicycle clearance from a 2”... -
Page 5: Introduction
..........IT, puis l’installer et le fixer au Bump-IT avec la même tige Installation . -
Page 6: Information D'installation Pour Le Jack-It
COMPORTE DES RISQUES DE SÉCURITÉ ET PEUT offertes individuellement. Toutes les pièces avec un lien vers CAUSER LA MORT, DE GRAVES BLESSURES la boutique de Lippert Components peuvent être achetées. PERSONNELLES, DES DOMMAGES IMPORTANTS AU PRODUIT OU À LA PROPRIÉTÉ. S’ASSURER Outils requis D’EFFECTUER UNE INSTALLATION SÉCURITAIRE ET... -
Page 7: Fixation À Un Attelage Avec Tube Receveur De 1,25 Po
Fixation à un attelage avec tube receveur de 1,25 po Fixation du BikeWing au Bump-IT 1. Faire glisser le tube du Bump-It dans le receveur de 1. Détacher la base du BikeWing du porte-vélos Jack-IT l’attelage du véhicule et aligner les trous de la tige. -
Page 8: Fixation Des Vélos
5. Répéter les étapes 2 à 4 pour installer un deuxième vélo de l’autre côté du porte-vélos. Dégagement de montage ≈ 17po Le Bump-IT mesure 22,5 po de l’avant vers l’arrière, avec un dégagement intérieur de vélo d’environ 17 po de la face d’un receveur de 2 po (Fig.4). 22,5 po Capacité...