Mounting And Operation - HIKOKI CR 12DA Mode D'emploi

● Regarding the temperatures and charging time of the
battery.
The temperatures and charging time will become as
shown in Table 2.
Table 2
Battery
Charging voltage
Type of battery
Temperatures at which the
battery can be recharged
Charging time for battery
capacity, approx.(At 20°C)
1.5 Ah
2.5 Ah
4.0 Ah
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
In addition, the charge time becomes signifi cantly long in
a low temperature environment, but this is not abnormal.
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (off for 0.5 seconds). In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger's
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
○ Since the built-in micro computer takes about 3
seconds to confi rm that the battery being charged with
charger is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
○ If the pilot lamp does not blink in red (every second)
even though the charger cord is connected to the power,
it indicates that the protection circuit of the charger may
be activated.
Remove the cord or plug from the power and then
connect it again after 30 seconds or so. If this does
not cause the pilot lamp to blink in red (every second),
please take the charger to the HiKOKI Authorized
Service Center.
Charger
UC12SL
V 10.8 – 12 Peak
Li-ion
0°C – 50°C
min. 22 (3 cells)
min. 37 (3 cells)
min. 60 (3 cells)

MOUNTING AND OPERATION

Action
Removing and inserting the battery
Charging
Remaining battery indicator
Switch Operation
Mounting the blade
*2
Mounting the Jigsaw blade
Dismounting the blade
Select a saw blade of the
appropriate length
Fasten a workpiece fi rmly
Adjusting the base
Plunge cutting (for wood)
Selecting accessories
*1 Make sure that the battery is installed fi rmly. If it is at all
loose it could come off and cause an accident.
*2 Mounting the blade
(1) Turning the blade holder in the direction indicated by
the arrow, insert the blade all the way into the small
slit of the blade holder. (Fig. 6-b)
(2) The blade will be locked in place when the blade
holder is released.
The blade can be attached facing up or down
depending on the operation.
(3) Pull the back of the saw blade two or three times by
hand and check that the blade is securely mounted.
(Fig. 6-c)
NOTE
The blade can be mounted without fi tting it into the base.
However, in this case, always make sure that the base is
attached to the tool after mounting the blade.
*3 Mounting the jigsaw blade (sold separately)
A T-shank jigsaw blade can be used with this product.
(Fig. 6-a)
Mounted in the same manner as a reciprocating saw
blade. Make sure that the shank of the blade is fi tted into
the center cavity. (Fig. 7)
Pull the back of the saw blade two or three times by hand
and check that the blade is securely mounted. (Fig. 6-c)
*4 Dismounting the blade
CAUTION
Never touch the saw blade immediately after use. The
metal is hot and can easily burn your skin.
(1) After turning the blade holder, point the blade downward.
The blade should fall out on its own. If the blade fails to
fall out, pull it out by hand.
WHEN THE BLADE IS BROKEN
Even when the saw blade is broken and remains inside
the small slit of the blade holder, it should fall out when
the blade holder is turned, and the blade is pointed
downward. If the blade fails to fall out on its own, take it
out by using the procedures described below.
(1) If a part of the broken saw blade is sticking out of the
small slit of the blade holder, pull out the protruding part
and take the blade out.
(2) If the broken saw blade is hidden inside the small slit,
hook the broken blade using a tip of another saw blade
and take it out. (Fig. 8-b)
11
English
Figure
2
*1
3
4
5
6
7
*3
8-a
*4
9
10
11
12
*5
―
Page
2
2
2
3
3
4
4
4
5
5
5
105