Need help? 1.800.762.1142
Do not return to place of purchase.
Installing LP Gas Tank
To operate, you will need one precision-filled standard LP grill gas
tank with external valve threads.
W CAUTION: LP gas tank must be properly
disconnected and removed prior to moving this
outdoor fireplace.
Inserting LP Gas Tank
W WARNING: Make sure LP gas tank valve is closed.
Place precision-filled LP gas tank upright into hole in the base of the outdoor fireplace so the
tank valve is facing the gas line connection.
Secure LP Gas Tank
Secure tank by sliding tank retainer chain around the LP gas tank and insert peg into LP gas
tank tray.
Note: Peg must be inserted into LP gas tank when tank is in LP gas tank tray.
Connecting LP Gas Tank
1.
Before connecting, be sure there is no debris caught in the
head of the LP gas tank, head of the regulator valve or in the
head of the burner or burner ports.
2.
Connect regulator/hose assembly to tank by turning knob
clockwise until it stops.
Disconnecting LP Gas Tank
1.
Before disconnecting, make sure the LP gas tank valve is
"CLOSED."
2.
Disconnect regulator/hose assembly from LP gas tank by
turning knob counterclockwise until it is loose.
W CAUTION: LP gas tank must be properly
disconnected and removed prior to moving
this outdoor fireplace.
3.
Place the protective cap cover on the LP gas tank and store
the tank outdoors in a well-ventilated area out of direct sunlight.
BlueRhino.com
Available in U.S. only.
Operating Instructions
Checking for Leaks
W WARNING: Before using this outdoor
20 lb
fireplace, make sure you have read,
9 Kg
understand and are following all
information provided in the "Dangers
and Warnings" section on page 2.
12.2 in. / 31 cm
Failure to follow those instructions
can cause death, serious injury or
property damage.
Burner Connections
1.
Make sure the regulator hose and valve
connections are securely fastened to the burner
and the tank.
2.
Visually check the connection between the
burner/venturi tube and orifice.
3.
Make sure the burner/venturi tube fits over the
orifice.
W WARNING: Failure to inspect
this connection or follow these
instructions could cause a fire or an
explosion which can cause death,
serious bodily injury or damage to
property.
4.
Please refer to diagrams for proper installation
(Figures 1 and 2).
5.
If the burner/venturi tube does not rest
flush to the orifice as shown, please contact
1.800.762.1142 for assistance.
Tank/Gas Line Connection
1.
Make 2-3 oz. of leak detection solution by
mixing one part liquid dishwashing soap with
three parts water.
2.
Make sure control knob is in the " OFF"
position (Figure 3).
3.
Connect LP gas tank per "Installing LP Gas
Tank" section.
4.
Turn LP gas tank valve to "OPEN."
5.
Spoon several drops of solution, or use a squirt
bottle, at all "X" locations (Figures 1 and 2).
a. If any bubbles appear, turn LP gas tank valve
to "CLOSED," reconnect and re-test.
b. If you continue to see bubbles after
several attempts, turn LP gas tank valve to
"CLOSED" and disconnect LP gas tank, per
"Disconnect LP Gas Tank" section. Contact
1.800.762.1142 for assistance.
c. If no bubbles appear after one minute, turn
LP gas tank valve to "CLOSED," wipe away
solution and proceed.
Lighting
W CAUTION: Keep outdoor gas
appliance area clear and free from
combustible materials, gasoline and
other flammable vapors and liquids.
W CAUTION: Do NOT obstruct the flow of
combustion and ventilation air.
W CAUTION: Check and clean burner/
venturi tubes for insects and insect
nests. A clogged tube can lead to a
fire.
W CAUTION: Attempting to light the burner with a cover on it may cause
an explosion.
1.
Make sure all labels, packaging and protective films have been removed from the outdoor
fireplace.
2.
Check for obstructions of airflow to the burner. Spiders, insects and webs can clog the
burner/venturi tube. A clogged burner tube can lead to a fire.
3.
Control knob must be in the " OFF" position (Figure 3).
4.
Clear small area of glass rocks or lava rocks away from the pilot housing.
5.
Connect LP gas tank per "Installing LP Gas Tank" section.
6.
Turn LP gas tank valve to "OPEN."
7.
Push and turn control knob to
8.
Continue to hold the control knob in, press the (electronic igniter) and hold for up to
5 seconds to light the pilot.
9.
Continue to hold the control knob in for 20 seconds to heat thermocouple.
10. After 20 seconds, release and turn control knob counterclockwise to ignite burner and
adjust flame to desired height.
Replacement Parts
parts.BlueRhino.com
1.800.762.1142
Figure 1
LP Gas
Connection
LP Gas Valve
with Orifice
Figure 2
X
X
X
Figure 3
OFF / ARRÊT
Figure 4
Figure 5
(LOW).
7
Burner Venturi
Pipe
Burner Supply
Tube
X
X
15.75 in. – 19.7 in.
40 - 60 cm