Conrad 55 85 82 Mode D'emploi page 3

O P E R A T I N G I N S T R U C T I O N S
Step counter with 3D sensor
& memory
Item no. 55 85 82
Intended use
The step counter is used to measure the number of steps and the duration of the activity. Based
on this measurement, the calorie consumption and the distance covered are calculated. The
data for the last seven training days are saved. The product also features an integrated clock.
The product is suitable for use in recreational sports but not in professional and medical meas-
uring technology. The measured values resp. indications of the product are not suitable for
commercial purposes or for publicly disseminating information.
The manufacturer is not responsible for incorrect displays or measured values and any conse-
quences which may arise thereof.
Any use other than described above may damage the product, there may also be other dan-
gers.
The safety instructions must be observed at all times!
The product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package content
• Step counter
• Mounting clip
• Battery
• Operating instructions
Explanation of the symbols
This symbol indicates specifi c risks associated with handling, function and use.
The "Hand" symbol indicates special tips and operating information.
Safety Instructions
First, read the complete operating manual carefully, it contains important in-
formation about the proper installation and operation of the product.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! The
warranty will be void in such cases!
• For safety reasons, any unauthorised conversion and/or modifi cation to the prod-
uct is not permitted. Never dismantle the product.
• If the product is used outdoors, it must be protected from humidity.
• This product is not a toy and must be kept out of the reach of children. Use the
product only out of the reach of children; the product contains parts and batteries
that can be swallowed.
• Condensation may form when the product is brought from a cold room into a warm
one. Therefore, wait until it has reached room temperature before using it.
• Do not leave packaging material carelessly lying around, as it could become a
dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or accidental
falls, even from a low height.
• If it can be assumed that safe operation is no longer possible, the device must be
turned off and precautions must be taken to ensure that it is not used unintention-
ally. After this, arrange for an expert to check the product. Safe operation is no
longer possible, if the product:
- has visible damages,
- no longer functions properly,
- has been stored for a longer period under unfavourable ambient conditions or
- has been exposed to considerable strain during transport.
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
Controls and Parts
www.conrad.com
(1) Display
Version 07/13
(2) SET key
(3) RESET key
(4) MODE key
Getting Started and Operation
a) Settings
• Press the MODE button (4) until the STEP display appears on the display.
• Press and hold the SET button (2) until SETUP appears on the display.
• Set the desired time format (12h or 24h format) using the keys RESET (3) or MODE (4).
• Press the SET key (2) to set the next value (here, seconds).
• Set the other values for the hours, minutes, month, date, year, measuring units, step length,
body weight and target steps per day as described above.
• The values can be increased using the RESET key (3), and decreased using the MODE key
(4).
• Press the SET key (2) to access the setting for the next value to be set and press this key at
the end of the setting process to save the set values and to return to normal mode.
b) Attaching the product to clothes
• Insert the product in the mounting clip provided.
• Fasten your step counter with the mounting clip preferably in the hip area on your clothing.
c) Operation
• In normal mode, the steps and the time are displayed (STEP display).
• At midnight, the values measured daily are reset so that the display always refers to a calen-
dar day.
• Press the MODE key (4) to access the different display modes one after another:
STEP
KM/MILE
KCAL
MIN
STEP
TOTAL STEP
Remove the insulating pad in the battery compartment. This pad protects the battery
from discharging during transport. To this end, please also observe the section "Bat-
tery replacement" further on in this manual.
Prior to carrying out the measurements, measure your average personal step
length. For this purpose, walk or run ten steps and measure the distance covered. If
you divide this measured distance by ten, you will get a relatively accurate value of
your personal step length.
If no keystrokes are performed for ten seconds, the step counter automatically
switches back to normal mode.
To avoid faulty measurements, the step counter must not be exposed to
strong blows, magnetic fi elds, electro-magnetic fi elds or strong vibrations.
Do not hang the step counter around your neck and do not place it into the
back pockets of your trousers.
The display switches on automatically when motion is detected.
To avoid unintentional measurements, steps will be measured only after the device
has detected steps for a period of fi ve seconds. These fi rst steps are not displayed
initially, however they will be included in the measurement.
Upper display line: steps count current day
Bottom display line: Time
Upper display line: distance covered in km/miles current day
Bottom display line: Time
Upper display line: calories burnt current day
Bottom display line: Time
Upper display line: Duration of training current day
Bottom display line: Time
Upper display line: Data from daily memory
Bottom display line: Displays the saved day
Press the button RESET (3) to select the day to be displayed.
Press the SET (2) key to display the different data of the selected day.
Upper display line: Data from total memory since last reset
Bottom display line: Time
Press the SET (2) key to display the different data of the total memory.