Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Cal. 3540.D
English
User's Manual
Description of the display and control buttons
Display elements
Minute hand
Centre stop-second
1
⁄
second counter
10
(hour counter after 30 minutes)
Minute counter
Hour hand
Second hand
Date
1
⁄
second counter
10
4
Push-button A
Minute counter
Push-button B
1
⁄
second counter
Centre stop-second
10
I
II
III
Minute counter
Push-button A
III
Push-button B
I
II
III
Second hand
I
II
III
Crown
I
II
Date
I
II
Control buttons
Push-button A
Crown
Push-button B
Chronograph:
Accumulated timing
Example:
Start:
(start timing)
Stop:
(e.g. 15 min 5 sec following
Restart: (timing is resumed)
4
*
Stop:
(e.g. 13 min 5 sec following
=
28 min 10 sec
(The accumulated measured time is shown)
Reset:
The 3 chronograph hands are returned to
their zero positions.
Please note:
* Following
, the accumulation of the
4
timing can be continued by pressing
push-button A
(Restart / Stop, Restart / Stop, ...)
Adjusting the chronograph
hands to zero position
Example:
One or several chronograph hands are not
in their correct zero positions and have to be
adjusted (e.g. following a battery change).
Pull out the crown to position III
(all 3 chronograph hands are in their
correct or incorrect zero position).
Keep push-buttons A and B depressed
simultaneously for at least 2 seconds
(the centre stop-second rotates by
360° corrective mode is activated).
Setting the time
*
P ull out the crown to position III
(the watch stops).
Turn the crown until you reach the correct
time 8:45.
* Push the crown back into position I.
Please note:
* In order to set the time to the exact second,
must be pulled out when the second
hand is in position «60» (I).
Once the hour and minute hands have been
set,
must be pushed back into position I
at the exact second.
Setting the date/time
Example:
– Date / time on the watch:
17
– Present date / time:
4
Pull out the crown to position II
(the watch continues to run).
Turn the crown until yesterday's date
appears
.
3
www.ronda.ch
ROnDA is a supplier of watch movements including their operating instructions.
Please refer to the watch retailer, service centre or manufacturer, should you have any
questions regarding the watch. All relevant contact information can be found in your
sales and/or guarantee documents.
Battery type: 384 (diameter 7.9 mm x 3.6 mm / SR 41 SW)
Accuracy: +20 / -10 seconds per month
1
⁄
second counter
10
Minute counter
1
⁄
second counter
10
)
)
Minute counter
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
I
/ 1:25 AM
/ 8:30 PM
Chronograph: Basic function
Push-button A
(Start / Stop / Reset)
Example:
Start: Press push-button A.
Stop:
to stop the timing, press
push-button A once more and read
the 3 chronograph counters:
4 min / 38 sek /
Zero positioning:
Press push-button B.
(The 3 chronograph hands will be reset to
their zero positions).
Push-button B
Chronograph:
Push-button A
Intermediate or interval timing
4
Example:
Start: (start timing)
Display interval:
e.g. 10 minutes 10 seconds (timing
continues in the background)
*
Making up the measured time:
(the 3 chronograph hands are quickly
Push-button B
advanced to the ongoing measured time).
Stop: (Final time is displayed)
4
Reset:
The 3 chronograph hands are returned to
65,5% = 40mm Druchmesser
their zero position
Please note:
* Following
mediates can be displayed by pressing
push-button B (display interval / make up
measured time, ...)
Push-button B
65,5% = 40mm Druchmesser
A
Adjusting the centre stop second
A
Single step
A
Continuous
Adjusting the next hand B
B
Adjusting the
1
⁄
second counter hand (position 6h)
A
10
A
Single step
A
Continuous
Adjusting the next hand B
B
Adjusting the minute counter (position 9h)
A
A
Single step
A
Continuous
Returning the crown to position I
II
III
Termination of the chronograph hands
adjustment (can be carried out at any time).
Setting the date (quick mode)
Pull out the crown to position II (the watch
continues to run).
I
II
Turn the crown backwards until the correct
date
1
Push the crown back into position I.
Please note:
The date can be changed during the date
changing phase between 08:30 PM and
I
II
12:00 PM; please note that the date must be
set to the date of the following day as in this
case the automatic date changing does not
occur at midnight.
* Pull out the crown to position III
(the watch stops).
Turn the crown until the correct date
4
appears.
I
II
III
4
** Continue to turn the crown until the
correct time 8:30 PM appears.
Second hand
Push the crown back into position I.
4
Please note:
I
II
III
* To set your watch to the exact second,
please refer to the chapter entitled
«setting the time».
** Please observe the AM/PM clock rhythm.
7
⁄
sec
10
, further intervals or inter-
1 x short
long
III
III
III
1 x short
long
III
III
III
1 x short
long
III
III
appears.
Publicité
Table des Matières
