Master BLAST BT Mode D'emploi page 3

BLAST BT
battery-powered radio wind sensor
Dear customer, thank you for purchasing a MASTER product. This guide contains information about the product use. Before the product installation and use, please read carefully this
guide and keep it for future reference. The device is designed for the control of tubular motors for moving awnings and the like. Any other use beyond the field defined by Master S.p.A.
is prohibited and involves, as well as the failure to comply with instructions provided in this guide, the cancellation of Master S.p.A. liability and warranty. The installer, after the
installation of the product, must teach the end user about the working way of the automation and provide him with the user manual.
This sensor does not protect awning in case of strong and sudden gusts of wind. In case of weather hazards of this type, make sure that the curtains remain closed! Master
S.p.A. declines all responsibility for damage incurred due to weather events not detected by the device.
Disposal
MASTER uses packaging recyclable materials. Dispose materials on the proper containers, complying with the law in force in your locality.
This product may have substances that are polluting for the environment and dangerous for the health.
At the end of the product life cycle, carefully comply with the waste disposal rules. It is strictly forbidden to dispose the product on the domestic waste.
Notes on radio systems
It is advisable to avoid using radio systems in areas with strong interference (for example, near police stations, airports, ports, hospital, etc). A technical inspection is in any case
advisable before installing any radio system in order to identify sources of interference.
Radio systems can be used where possible disturbances or malfunctioning of the transmitter or the receiver do not cause a risk factor, or if the risk factor is cancelled by suitable safety
systems. The presence of radio device operating on the same transmission frequency (433,42 MHz) can interfere with the radio receiver of the motor and so reduce the range of the
system and limit the functionality of the installation.
Technical specifications
Power supply: 3V CR8-LHC battery
Dimension: 236 x 54 x 73 mm
Weight: 200 gr
Operating temperature: –20°C / +55 °C
Wind threshold: 10 Km/h / 35 Km/h
Sun threshold (VEGA BT only): 1 Klux / 45 Klux
Operating frequency: 433.42 Mhz
Operating frequency band: 433,050 – 434,790 Mhz
Max radiated power, e.r.p. : <10 mW
Range (estimated): 20m
01. MOUNTING
01.1 Warning for safety
Incorrect installation can cause serious injuries
programming and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions
given in this manual ● The wiring must comply with current IEC standards. The final electrical system must be created only by the electrician
operation and can exclude the use of radio controls or require particular safety devices
shutter/awning regularly
01.2 Warning for installation
Read the technical specifications on the paragraph "Technical specifications" to evaluate the operating limits of the product
Before installing the product, check the compatibility with the associated devices and accessories
intact and has not been damaged in transit
external or internal parts of the product
without the manufacturer's permission
ensure a stable fixation ● Check that the place chosen for the installation of the sensor is within the range of transmission-
reception generated by the sensor and by the receiver of the blind to be commanded
downwards and with the body of the sensor horizontally (using a bubble level facilitates the operation, the attack on the wall with
tilting angle ± 90 ° allows you to mount the sensor on non-vertical structures)
the sun-wind, away from heat sources (eg chimneys), away from obstacles that may interfere with the movement of the cups
there are several radio appliances in the same system, they must not be less than 1,5m apart
metal surfaces ● Do not use abrasive or solvent product for cleaning the device; do not clean using water or high-pressure
cleaners ● For your safety, do not work near the winding roller while the motor is powered
01.3 Warning for use
The product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they are supervised or given instructions about the product way of use by a person
responsible for their safety ● Check the automation during the movement and keep people at a safe distance, until the
movement ends ● Do not allow children to play with the appliance or with the fixed control devices
when maintanance operations are being carried out (e.g. window cleaning, etc.). If the control device is automatic, disconnect
the motor from the power line
01.4 Mounting
(1)
A B
Fix the wall support Close the two screws
through the supplied that fix the wall support
plugs and screws and sensor
(1) WARNING: this screws must never be completely unscrewed
(2) WARNING: when you slide the switch in the ON position, the LED1 should light up brieflyIf LED1 do not turn on, return the switch to OFF (1) position, wait 30 seconds and repeat.
● Keep these instructions for future maintenance work and disposal of the product
● A heavy shock and the use of unsuitable tools can cause the damage of the
● Do not pierce or tamper with the product in any way. Do not modify or replace parts
● Check that the place chosen for the installation is made by solid material and can
C
Insert the two screw
cover
433,42 MHz
● To prevent potentially dangerous situations, check the operating condition of the roller
● Check that the package is
●
Install the product with the cups pointing
● The product must be installed well exposed to
● Do not install the product near
● Do not operate the blind
D E (2)
Unscrew the screw and To power the sensor slide the switch from
open the closing cover
placed under the sensor
R
battery-powered radio sun/wind sensor
● All the product installation, connection,
● Some applications require hold-to-run
X
●
● If
Led WIND
Button P1
Led SUN
Button P2
OFF (1) to ON
VEGA BT
rev04 22.07.2017
Led MANOEUVRE
Button P3
F
Close the cover