Roadstar PCD-435CD Manuel D'instructions page 4

the battery compartment.
3. Close the battery compartment door.
Note: If the symbol " " flashes in the display, batteries are weak and ought to be replaced.
EARPHONES
Connect the stereo earphones (included) to the Phones jack (11).
CD PLAYBACK
1. Connect the earphones (included) or optional headphones into the Phones jack.
2. Press the Door Open button (8) to open the CD compartment door.
3. Insert a disc with the label side facing up.
4. Close the CD compartment door until a click is heard.
5. Set the VOLUME control (10) to minimum.
6. Press the PLAY/PAUSE ( >II ) button (6), the unit power will turn on automatically and start
playback.
The total number of tracks and total playing time appear on the display. Playback starts.
During playback, the actual track and the elapsed time appear.
7. Adjust the VOLUME control to your desired listening level.
8. To stop playback temporarily, press the PLAY/PAUSE ( >II ) button (6) once. The elapsed time
will flash on the display. Press the PLAY/PAUSE ( >II ) button again to resume playback.
9. To stop playback, press the STOP (5) button once.
10. To turn the unit off, press the STOP (5) twice.
Notes:
• When the CD door is accidentally opened during playback, "
display.
• Wait until the disc is fully stopped before pressing the OPEN button.
• This unit can play 3" (8cm) single CDs without an adaptor.
LOCATING A PARTICULAR TRACK OR POINT OF THE TRACK
1. Press the - SKIP/SEARCH ( ) (3) button once to go back to the beginning of the current
track.
2. Press the - SKIP/SEARCH ( ) (3) button repeatedly to go back to previous tracks.
3. Press the +SKIP/SEARCH () (4) button repeatedly to go to next tracks.
4. Press and hold either +SKIP/SEARCH () or - SKIP/SEARCH ( ) button to search
English 3
" will appear on the
4 English
backwards or forwards, at high speed, a particular point of track.
Note: Low level audio will be heard during the search process to assist in locating the correct
point in the track.
REPEAT PLAYBACK
1. Press the PLAY/PAUSE button (6).
2. To repeat the same track, press the MODE button (2) once. The"
on the display. The CD will start single repeat playback until STOP button (5) is pressed.
3. To repeat the entire disc, press the MODE button (2) twice. The "
appear on the display.
INTRO PLAY
1. Press the PLAY/PAUSE button (6) and after 5 seconds the STOP button (5).
2. Press the MODE button (2) three times to enter the Intro mode, 'INTRO' appears on the
display.
3. Press the PLAY/PAUSE button, CD will play the first 10 seconds of each track on the CD.
4. Press MODE button (2) once more to cancel Intro playback and resume normal playback.
5. Power is turned off automatically after 30 seconds, when all tracks have been played.
RANDOM PLAY
1. Press the PLAY/PAUSE button (6) and after 5 seconds the STOP button (5).
2. Press the MODE button (2) to enter the Random mode. "RND" flashes on the display
3. Press PLAY/PAUSE button (6) to start playback in Random order.
4. Press SKIP Forward () button (4) to go to next Random track.
5. Press the MODE button once more to return to the Normal Playback mode.
PROGRAMMED PLAYBACK
1. Press the PLAY/PAUSE button (6) and after 5 seconds the STOP button (5).
2. Press the PROGRAM button (1). The track number and the program number will appear and
"PROG" will flash on the display indicating the first selection.
3. Press - SKIP/SEARCH ( ) or +SKIP/SEARCH () button to select the desired track to be
programmed. The track number which will be programmed will appears on the display.
4. Press once the PROGRAM button (1) to enter the track into memory.
5. Repeat the steps 3 and 4 to program up to 20 tracks.
1" indicator will appear
ALL" indicator will