Drill Safety Warnings; Additional Safety And Working Instructions - BTI A18 SBS BL-3 Notice Originale

TECHNICAL DATA CORDLESS PERCUSSION DRILL/DRIVER
Code ........................................................................................
Drilling capacity in steel ...........................................................
Drilling capacity in wood
with fl at bit .............................................................................
with auger bit ........................................................................
with hole saw ........................................................................
with selfeed bit ......................................................................
Drilling capacity in brick and tile ..............................................
Wood screws (without pre-drilling) ..........................................
No-load speed 1st gear ...........................................................
No-load speed 2nd gear ..........................................................
Impact rate 1st gear.................................................................
Impact rate 2nd gear ...............................................................
Torque with battery (5.0 Ah).....................................................
Battery voltage.........................................................................
Drill chuck range ......................................................................
Weight according EPTA-Procedure 01/2014 (1.5 Ah / 2.0 Ah)
Weight according EPTA-Procedure 01/2014 (3.0 Ah / 4.0 Ah)
Recommended ambient operating temperature ......................
Recommended battery types...................................................
Recommended charger ...........................................................
Noise/vibration information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ........................
Sound power level (Uncertainty K=3dB(A)) .............................
Always wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
h
Percussion drilling into concrete a
Uncertainty K= ......................................................................
Drilling into metal a ............................................................
h,D
Uncertainty K= ......................................................................
Screwing a ...........................................................................
h
Uncertainty K= ......................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live" and could
give the operator an electric shock.
Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Brace the tool properly before use. This tool produces a
high output torque and without properly bracing the tool
457 528 - A18SBS BL-3.indd 21 457 528 - A18SBS BL-3.indd 21
...... A18SBS BL-3 01 00001- 99999
...........................13 mm
...........................32 mm
...........................32 mm
...........................89 mm
...........................65 mm
...........................16 mm
...........................16 mm
......................0-550 min
....................0-2000 min
....................0-8800 min
..................0-32000 min
.........................135 Nm
...........................18 V
.....................1,5-13 mm
........................1,88 kg
........................2,18 kg
...................... -18...+50 °C
.............. A18V - 2Ah, 5Ah, 9Ah
... A14,4-18V LG, A14,4-18V SLG M-A
......................97,75 dB (A)
....................102,75 dB (A)
.................................... ......................10,39 m/s
h,ID
..........................1,5 m/s
..........................1,9 m/s
..........................1,5 m/s
..........................1,6 m/s
..........................1,5 m/s
21
A18SBS BL-3
-1
-1
-1
-1
2
2
2
2
2
2
during operation, loss of control may occur resulting in
personal injury.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed
rated of the drill bit. At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the
workpiece, resulting the personal injury.
Always start drilling at low speed and with the bit tip in
contact with the workpiece. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting the personal injury.
Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal injury.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
ENGLISH
19.02.2019 11:00:45 19.02.2019 11:00:45