Vivanco UR 810 Mode D'emploi page 2

Manual code search
1. Switch on the appliance to be
controlled. Program is running.
2. To prepare code search, press the
SET button, keep it pressed and then press the
required appliance button, e.g. TV, additionally
until the lamp (LED) lights constantly.
3. Then point the remote control at the
appliance to be controlled.
4. Briefly press the ON/OFF
(appliance on/off) button once. The lamp (LED)
blinks. – Except when searching for a TV code
you can also briefly press the yellow > (Play)
button and use the Play function to search.
Make sure that a tape, a DVD or a CD is
inserted in the tape deck, player or recorder.
5. Press the ON/OFF
on/off) or Play button repeatedly, approx. every
1,5 seconds, until the appliance, e.g. your DVD
player, reacts. - If you notice the reaction of
your appliance too late and the next code has
already been emitted you can go back by
pressing SET and then ON/OFF or Play again.
If your appliance has switched itself off you
must switch it back on again, e.g. on the
appliance or with the original remote control, to
continue searching. - When your appliance
reacts you can also try out other buttons
without interrupting the search. If some buttons
do not work properly, simply
searching with ON/OFF or Play.
6. When your appliance
correctly, press the appliance button, e.g. TV,
and end the search. The lamp (LED) goes out.
- The UR 810 continues with the search at the
point where you interrupted it. When the end of
the code list is reached the search stops
automatically. The remote control blinks quickly
several times. The code last entered remains
stored. The search stops after approx. 30
seconds of inactivity.
Automatic code search
Your remote control finds the correct settings
almost automatically in seconds:
1. Switch on the appliance to be
controlled. A channel number, for example,
appears in the display of your satellite receiver.
2. To start the code search, press the
SET button, and then additionally the required
appliance button, e.g. TV, for more than 3
seconds until the lamp (LED) starts to blink.
3. Then point the remote control at the
appliance to be controlled while the remote
control emits a different ON/OFF signal every 2
seconds.
4. When your appliance reacts, press
any button, except SET, to end the search. – If
Vivanco GmbH, D-22926 Ahrensburg, E-Mail
UR 810 UNIVERSAL CONTROLLER
you ended the search too late, continue to
search using the Manual Code Search (see
above).
5. Finally, test the control code setting
by trying to control, for example, your DVD
appliance. If it does not work correctly, please
try the code search again. The code search
then begins with the next code in the
sequence. -
appliance, e.g. DVD, back on again if you wish
to continue searching.
Code identification
You can read off the 3-digit codes you have set
at any time:
1. Press the appliance button of the
appliance which code you want to read off, e.g.
TV.
(appliance
2. Press the SET button and 1,2,3,
depending on the part of the code you want to
read off. For example, if you press SET+1 after
TV and the code 156 (in this example) has
been set, the lamp blinks once after SET+1 is
released to show that the hundred figure is 1.
All you have to do is count. The ten figure is
indicated after SET+2 is released, e.g. it blinks
5 times for the 5 in 156. The one figure is
indicated after SET+3 is released, e.g. it blinks
6 times for the 6 in 156.
Learning, Programming, of Missing Control
Functions
continue
The LEARN function is used to supplement the
preprogrammed codes. The standard code
reacts
may provide most of functions needed, but you
may miss some key functions. Or you didn´t
find any functioning preprogrammed code for a
device. You can capture upto 100 key funtion
codes, max 40 per device. The last captured
function will overwrite the previous. learnt.
1 For learning of key codes you must use a
functioning orginal remote controller. Please
use fresh batteries for both remote controls.
2 Please point the original´s remote control
transmitter LED towards the receiver LED of
UR 810 (placed on top, same as transmitter
LED). Distance of LEDs between both remotes
shall be approximately 30mm and must be in
straight line of sight.
3 Press down and hold the Learn key and
press the device key (e.g. DVD) additionally
and then release the both pressed keys. Then
e.g. the DVD device key starts blinking
indicating that DVD key codes (functions) can
be captured.
4 Press and release the target key, that
you want to learn to (reprogram) (e.g.
POWER), the device button lights up.
5 Press and hold the source key on the
: hotline@vivanco.de
, Helpline: +49 (0) 4102 231135
Remember to switch your
2