Sommaire des Matières pour Hydro-Gear HGM-12P
- Page 1 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 We set the wheels in motion. ® HGM-12P LSHT Wheel Motor Service and Repair Manual BLN-52197 October 2004 www.mymowerparts.com...
- Page 2 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 www.mymowerparts.com...
-
Page 3: Hydraulic Motors
Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Service Hydraulic motors HGM-P Spare parts list / service manual Index Page Exploded view: HGM-P ...................... Spare parts list ........................Tightening torque ......................... Dismantling .......................... Assembly..........................www.mymowerparts.com... - Page 4 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Exploded view HGM-P www.mymowerparts.com...
- Page 5 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Number per motor Series 8* Series 7 and 8 with separate spigot flange OMP C Item Spare parts Dimension Flange Flange Flange Flange Flange HGM-P Screw M6: L = 16 mm M5: L = 16 mm M6: L = 16 mm Dust seal ring...
- Page 6 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Number per motor Series 8* Series 7 and 8 with separate spigot flange OMP C Item Spare parts Dimension Flange Flange Flange Flange Flange HGM-P Washer 44,0 × 20,5 × 4,0 for 28,5 mm tapered shaft Parallel key for ∅25 mm shaft...
- Page 7 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Number per motor Series 8* Series 7 and 8 with separate spigot flange OMP C Item Spare parts Dimension Flange Flange Flange Flange Flange HGM-P End cover Side port motor without drain Side port motor End port motor Washer...
- Page 8 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Number per motor Series 8* Series 7 and 8 with separate spigot flange OMP C Item Spare parts Dimension Flange Flange Flange Flange Flange HGM-P Spar part bag for motors with HPS and ∅25 mm, ∅1", 1”...
- Page 9 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Notes Dismantling Item Part to remove Comments Castelated nut Washer Parallel key Seal plugs Placer motor i holdeværktøj med udgangsaksel nederst. Ved endeportsversion benyttes 10 mm unbrakonøgle. Put the motor in a holding tool, with the output shaft downward. For end port version use 10 mm hexagon socket spanner.
- Page 10 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Dismantling Item Part to remove Comments 21, 20 Screws, washers Benyt 13 mm topnøgle. Use a 13 mm spanner socket. Einen 13 mm Steckschlüssel verwenden. Utiliser clé à douille 13 mm. End cover Fjern endedækslet sideværts.
- Page 11 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Dismantling Item Part to remove Comments Screws (6 off) Anvend Torx-nøgle type T30, 9 mm skruetrækker eller 4 mm (If present) unbrakonøgle. Use Torx-spanner type T30, 9 mm screwdriver or 4 mm hexagon socket spanner.
- Page 12 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Dismantling Item Part to remove Comments Kun OMP/OMPW N med ∅32mm/28,5 mm konisk aksel. Bearing race Anvend 2 mm skruetrækker. Only HGM-P with ∅32 mm/28,5 mm tapered shaft. Use a 2 mm screwdriver. Nur OMP/OMPW N mit ∅32 mm/28,5 mm kegelige Welle.
- Page 13 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Assembly Item Part to mount Comments Placer motorhuset i holdeværktøjet med flangen øverst. Place the motor housing in the holding tool with the flange upwards. Das Motorgehäuse mit dem Flansch nach oben im Haltewerk- zeug anbringen.
- Page 14 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Assembly Item Part to mount Comments Dust seal ring Anbring støvtætningsringen i styreflangen og bank den på plads med en plasthammer og passende dorn. Place the dust seal ring in the spigot flange and knock it into position with a plastic hammer and appropriate mandrel.
- Page 15 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Assembly Item Part to mount Comments Screws (6 off) Tilspændingsmoment Torx skruer M6 : 0,5-0,8 daNm Kærvskruer M6 : 0,5-0,8 daNm Unbrakoskruer M5 : 0,5-1,0 daNm Vend herefter motoren. Tightening torque Torx screws M6 : 0,5-0,8 daNm(45-70 lbf in (in-lbs)) Slotted screws M6...
- Page 16 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Assembly Item Part to mount Comments O-ring Indfedt O-ring og læg den i husets O-ringsrille. Grease the O-ring and put it in the O-ring groove of the housing. Den O-Ring einfetten und in die O-Ring-Rille des Gehäuses legen.
- Page 17 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Assembly Item Part to mount Comments 18, 16 Gearwheel set, Placer O-ringene (indfedtet) i tandkransens O-ringsriller. O-rings I de tandhjul hvor splines ikke er gennemgående, vendes tand- hjulet så fridrejning vender ned mod huset. Placer tandhjulssættet på...
- Page 18 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 Assembly Item Part to mount Comments 20, 21 Washer, screws Benyt 13 mm topnøgle. Tilspændingsmoment: 3,0-3,5 daNm. Use a 13 mm spanner socket Tightening torque: 3,0-3,5 daNm (265-310 lbf in (in-lbs)). Den 13 mm Steckschlüssel verwenden.
- Page 19 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 www.mymowerparts.com...
- Page 20 Hydro Gear Parts or New Units Call 606-678-9623 or 606-561-4983 © 2004 Hydro-Gear. All rights reserved. Rev. P Printed in U.S.A. 310-0410 IHT www.mymowerparts.com...