Bluetooth ® Wireless Technology; Functions Of The Control Panel - Husqvarna DE 110S Manuel D'utilisation

To remove the dust extraction hose
• Push the hose lock button (A) and pull the dust
extraction hose. (Fig. 6)
To attach and adjust the floor nozzle
1. Put the end of the handle fully into the shaft of the
floor nozzle. (Fig. 7)
2. Turn the knob (A) at the rear of the floor nozzle
to adjust the floor nozzle wheels. Different surfaces
and different types of dust and materials make it
necessary to adjust the wheels to get the best
performance. (Fig. 8)
®
Bluetooth wireless technology
Products with built-in Bluetooth
can connect to mobile devices and enables additional
functions from Husqvarna connect.
Bluetooth
The symbol for
on when your mobile device is connected to the product.
(Fig. 9)
To use embedded connectivity with
fleet
Note:
This part is applicable only for products
supplied with embedded connectivity.
Note:
Radio transmission by the Bluetooth
will be enabled on the first time of connection to a power
outlet, and stay on after that.
1. Download the Husqvarna Fleet Services iOS or
Android app Husqvarna Fleet Services.
2. Go to Husqvarna Fleet Services website https://
fleetservices.husqvarna.com for more information.
To lock and unlock the transport
wheels
For operation on a surface with a slope it is necessary to
lock the transport wheels.
WARNING:
must be clean and without dust for safe
operations. Refer to
on page 16 .
1. Hold the product in a stationary and safe position.
2. Push down the wheel brake on each side to lock the
wheels. (Fig. 10)
Note:
DE 110S/DE 110 has only 1 wheel brake.
3. Pull up the wheel brakes to unlock the wheels.
14
®
wireless technology
®
wireless technology comes
®
function
Wheels and bearings
Maintenance schedule

Functions of the control panel

The control panel controls and monitors important
functions and setups of the product. Refer to
on the control panel (DE 110/DE120) on page 20 to
find solutions for the warnings.
(Fig. 11)
1. The prefilter is clogged. Refer to
particles from the prefilter during operation on page
15 .
2. The HEPA filter is clogged, damaged or missing.
Warnings on the control panel (DE 110/
Refer to
DE120) on page 20 .
Warnings on the control panel (DE
3. Warning. Refer to
110/DE120) on page 20 .
®
4. Bluetooth connection. Refer to
connectivity with fleet on page 14 .
5. Diameter change function for hose, refer to
the hose nozzle diameter on page 15
6. Automatic start, refer to
(Only 230V DE 110S and DE 110) on page 14
7. e-Flow button, refer to
8. On/Off button
e-Flow function
The product has an e-Flow function. This function
automatically adjusts the airflow to the workload for
optimal performance. The product always starts with the
last settings used.
Functions of the control panel on page 14 to
Refer to
engage or disengage the function.
Automatic start function (Only 230V DE 110S
and DE 110)
The product can be used to collect dust from equipment
such as a grinder or power cutter. When you start
the equipment that is connected to the electrical outlet
on the product, the product starts automatically. When
you stop the equipment, the product operates for
approximately 10 seconds to empty the hose and then
stops.
Airflow warning system
The airflow in the suction hose must be more than 20
m/s (66 ft/s).
For the minimum airflow with the selected hose diameter
refer to the table.
DE 110
in.(mm) CFM (m
1 (27) 24 (41)
1 ¼ (32) 34 (58)
Warnings
To remove dust
To use embedded
To select
Automatic start function
e-Flow function on page 14
DE 120
3
/h) in.(mm) CFM (m
1 ½ (38) 48 (82)
1 ⅔ (42) 59 (100)
1587 - 007 - 24.01.2022
3
/h)