Technical Data - Clatronic AR 735 CD Mode D'emploi

Technical data

General
Supply voltage .............................................................. DC 12 V
Power consumption ......................................................7 A max.
Power..............................................................................4 x 7 W
FM band
Frequency range................................... 87,5 MHz to 108,0 MHz
Effective sensitivity ...........................................................10 μV.
I.F. frequency ...............................................................10,7 MHz
AM band
Frequency range........................................514 kHz to 1640 kHz
(Line-Out)
Output ....................................................................max. 800 mV
CD player
System ............................................................CD Audio System
Suitable CDs ....................CD/CD-R/CD-RW/MP3 disks (12 cm)
Playable bit rates .................................................32 - 320 kBit/s
Number of quantising bits ................................................... 1 bit.
Signal format ...............................Sampling frequency 44,1 kHz
Frequency characteristics ........................... 20 – 100 Hz ≤ 5 dB
Signal-to-noise ratio ..............................................50 dB (1 kHz)
Number of channels .......................................2 stereo channels
Housing dimensions ........................178 x 50 x 157 (W x H x D)
Net weight: ...................................................................... 1,43 kg
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
58
05-AR 735 CD.indd 58 05-AR 735 CD.indd 58
........................... 10 – 20 kHz ≤ 5 dB
Troubleshooting
Before going through the checklist please make all the con-
nections fi rst. If you still have questions after going through the
checklist, please consult your local customer service representa-
tive.
Fault Symptoms Cause
CDs are drawn only The transport screws
half way into the CD have not been
tray. removed.
„ERROR 2" is shown in The CD is inserted the
the display. wrong way round.
CD cannot be selected There is no CD
using the MOD button. inserted.
The volume control is
The CD does not play
set too low.
The device has
back after being in-
serted into the device. not been correctly
connected.
The surface of the road
is uneven.
The device is not fi rmly
installed.
CD works intermittently
(dropouts).
The CD is damaged.
The CD is dirty.
The device may have
been installed in the
vehicle at the wrong
angle.
The ignition is switched
off.
No function.
One or more fuses
have blown.
Incorrect connection
Device cannot be (each car manufacturer
switched on or off via wires the ISO con-
the ignition. nection in the vehicle
differently).
The microcomputer
The device does not
has been interfered
work correctly (EJECT,
with by electromagne-
LOAD, PLAY).
tic fi elds.
The antenna cable is
No radio reception.
not connected.
Solution
Remove the transport
screws.
Insert the CD right way
round.
Insert a CD.
Turn up the volume.
Check the +12V and
earth connection.
Wait until the road
becomes smoother
before playing the CD.
Install the device fi rmly.
Ensure that the rear at-
tachment is used if the
vehicle does not have
any suitable retainer
for the rear section of
the device.
Try another CD. If this
works correctly, the
fi rst CD is probably
damaged.
Clean the CD.
Please note that a
maximum inclination
of 20° degrees should
not be exceeded!
Turn the ignition key to
„ON" or „ACC".
Replace the fuse by
another 7 A /0,5 A
fuse.
Please contact your
car workshop or a
vehicle specialist for
connection adapters
may specifi cally for
your model.
Remove the CD or
cassette and reinsert it.
Switch the device off
and on again.
Insert the antenna
cable fi rmly into the
antenna socket of the
device.
17.10.2008 12:36:37 Uhr 17.10.2008 12:36:37 Uhr