Reinigung Und Wartung; Technical Data - UNIPRODO UNI TELESCOPE 01 Manuel D'utilisation

DE
3. Aufrichtendes Okular - dient zum Erhöhen der
Vergrößerung mit einem gegebenen Okular
während Bodenbeobachtungen und stellt die
korrekte Ausrichtung des Bildes des beobachteten
Objekts wieder her.
Achtung: Linsen und Filter sind im Okular auf
der dem Auge gegenüberliegenden Seite zu
installieren.

REINIGUNG UND WARTUNG

a) Verwenden Sie zur Reinigung der Oberfläche
ausschließlich Mittel ohne ätzende Inhaltsstoffe.
b) Bewahren Sie das Gerät an einem trockenen,
kühlen, vor Feuchtigkeit und direkter
Sonneneinstrahlung geschütztem Ort auf.
c) Verwenden Sie zur Reinigung ein weiches,
staubfreies und fusselfreies Tuch.
d) Lagern Sie das Produkt an einem Ort, der keinen
hohen oder niedrigen Temperaturen, Staub und
chemischen Mitteln ausgesetzt ist.
4
U S E R M A N U A L

TECHNICAL DATA

Parameter Parameter
description value
Product name Telescope
Model UNI_TELESCOPE_01
Aperture [mm] 60
Focal length 900
Finder 5x24
Dimensions [mm] 1250x840x1285
Weight [kg] 2,40
a) Do not look directly or through the lens on the
light source. This can cause eye damage and
epileptic seizures.
b) Do not leave the magnifying lens unattended in
places with direct sunlight as this creates a fire
hazard. After finishing work, remember to close
the lens cover.
c) It is forbidden to direct the focused light beam
towards people or animals. It may cause burns.
d) To avoid eye damage, do not use the product in
places where shocks can occur.
USE GUIDELINES
The product is intended for observing objects located
at a considerable distance from the user and for
astronomical observations.
The user is liable for any damage resulting from
unintended use of the device.
DEVICE DESCRIPTION
ATTENTION! This product's view can be found on the
last pages of the operating instructions (pp. 17).
1. Height adjuster
2. Focusing knob
3. Focus tube
4. Angle prism
5. Eyepiece
6. Finder bracket
7. Finder
8. Main tube
9. Sun visor
10. Lens
11. Clamp locking screw
12. Adjuster clamping screw
13. Clamp support
14. Azimuth lock
15. Tripod head
16. Accessories shelf
17. Tripod leg
18. Rubber foot
ASSEMBLY
ATTENTION! This product's exploded view can be
found on the last pages of the operating instructions
(pp. 17).
5 EN
1. Adjust the length of the tripod legs, then lock them
with the clamping screws (Fig. 1).
2. Connect the tripod legs with the tripod head using
the screw and the wing nut (Fig. 2a).
3. Fasten the accessories shelf with the screws and
nuts (fig. 3)
4. Install the main tube on the tripod head and
secure with the adjuster clamping
(Fig. 2b, c).
5. Install the finder bracket on the surface of the
main tube with the thumbscrews (fig. 4).
6. Install the angle prism on the focus tube and
secure with the adjusting screw (fig. 5).
7. Install the eyepiece at the angle prism, then adjust
its position and secure with the small adjusting
screw (Fig. 6).
8. If you are using optical accessories (e.g. Barlow
lenses), place them between the eyepiece and the
focus tube (Fig. 7).
FOCUSING THE TELESCOPE AND ADJUSTING THE
FINDER
Note: It is recommended to perform the following
activities in daylight.
1. Install the eyepiece with the lowest magnification
at the angle prism.
2. Point the telescope towards an easily recognizable
object. The object should be in the middle of the
telescope's field of view.
3. Secure the selected telescope position with the
clamping screws.
4. Look through the finder. Adjust its position using
the adjusting nut so that the object observed
through the telescope is in the centre of the finder
sight.
5. After adjusting the finder, secure its position with
the clamping screws.
EYEPIECE AND MAGNIFICATION
The telescope is equipped with several types of
eyepieces. The power of each eyepiece depends on the
focal length of the main mirror.
P= A
B
P. Telescope magnification
A. Focal length of the main mirror
B. Focal length of the eyepiece
FUNCTIONS AND ACCESSORIES
1. Barlow lens. When used with the telescope
eyepiece it extends the telescope's focal length
and, as a result, further enlarges the image of the
observed object.
2. Moon filter. Used with the telescope eyepiece
it reduces the light passing through the optical
system by means of polarizing filters.
3. Correcting eyepiece - serves to
magnification together with a given eyepiece
during ground observations and restores the
correct orientation of the image of the observed
object.
Note: The lenses and filters should be installed in
the eyepiece on the side opposite the eye.
screw
increase