Bimar HI-PET PBM1 SW 803 Mode D'emploi page 9

Copies of the I/B. Please reproduce them without any changes except under special
instruction from Bimar (Italy). The pages must be reproduced and folded in order to obtain a
booklet A5 (+/- 148.5 mm width x 210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't change the page numbering. Keep the
language integrity.
A
ttention: the temperature of the accessible surfaces may be very high when the appliance is in use.
M
ake sure not to touch these hot parts of the appliance.
INSTALLATION
• After removing the packing materials, check the integrity of the appliance; if you are unsure, do not
use it and ask for qualified professional help. The packing materials (plastic bags, polystyrene foam,
nails, etc.) must be kept out the reach of children because they are potential sources of danger; but
dispose of them in accordance with current law.
• Before connecting the appliance, check that the voltage shown on the data plate matches that of your
electricity and that the electric plug is grounded. In the event of incompatibility between the electric
outlet and the plug of the appliance, have the outlet replaced with another more suitable type by
professionally qualified personnel, who will make sure that the section of the wires of the outlet is
appropriate for the absorbed power of the appliance. In general, the use of adapters or extension cords
is not recommended; if their use is indispensable, they must conform to existing safety standards and
their current capacity (amperes) must not be less that the maximum of the appliance.
• Before each use, verify that the appliance is in good condition and that the electrical cord is not
damaged: in the case of doubt, ask for professionally qualified help.
• Do not scratch non-stick coating of cooking surfaces for fragments of the coating may be left in food.
Use a wooden spatula or plastic classic designed to withstand the heat.
• Make sure that the cable is correctly positioned, that it is not touching hot elements or sharp edges, is
not wound around the appliance, is not twisted up on itself or in the way to prevent the utensil from
being pulled over.
• Position the utensil far from other sources of heat, objects or anything else that could come into
contact with the hot parts. Check that the support surface is stable and flat to prevent the utensil from
tipping over.
• Never leave the appliance unattended when it is connected with the electric network; unplug after use.
• Place the appliance:
- far from other sources of heat (for example, other ovens, gas hobs, etc.), inflammable materials
(wallpaper, etc.), explosive materials (spray cans) and materials that would become deformed when
heated.
- on a flat and stable work top and not on delicate surfaces (painted furniture, tablecloths, etc.), in a
position where it cannot be bumped, and at a suitable distance from the edge so that it cannot fall.
- far from containers of liquids, such as sinks, etc. Should it unexpectedly become wet or fall in a
liquid, in the case of water overflows, immediately remove the plug from the power outlet, verify
that the electrical components of the appliance are not wet, and if they are, dry thoroughly and
carefully. Re-insert the plug into the socket, and then use the device. In case of doubt, contact a
qualified technician.
• It is absolutely necessary to keep this appliance clean at all times as it comes into direct contact with
food. Check the section "CLEANING AND MAINTENACE" in the instruction manual.
• In the case of a breakdown or fault, switch off the appliance and have it checked by a professionally
qualified technician; repairs made by unqualified persons can be dangerous and render void the
warranty.
USE
Before each use, verify that the unit is in good condition, the electric cord is not damaged, if the
power cord is damaged, it must be replaced by the manufacturer or a competent qualified electrician
or a person with similar qualifications, in order to avoid any risk.
When using for the first time
Before being used for cooking, the appliance should be switched on "empty" to eliminate the "smell
of new" and any oils remaining from the production process. Insert the plug in the power socket leave
the appliance on. When the cycle ends, remove the plug from the socket and wait until the appliance
is cool. These must be washed with damp cloth and dried.
9
Assembly page 9/20