Alarm Setting - UNITEC Climate 0787 Manuel De L'utilisateur

TIME SYCHRONIZATION
The unit will start synchronizing the clock after the 1st
channel (B) of the RF thermometer is registered. At
normal mode, hold „–" 3 button 3 seconds for force
synchronization. The antenna icon (I) will appear during
synchronization, if the icon disappear afterwards,
time signal is not available at the moment. Try other
locations later. Place the unit away from source of
interference such as mobile phones, appliances, TV
etc.Antenna icon (I) will appear fix on screen if the syn-
chronization is successful. The clock will have a daily
synchronization at 01:00 everyday. Maximum 4 more
attempts at one hour interval.

ALARM SETTING

Hold „CLEAR/ ALARM" 4 for 3 seconds. Press „+ 2,
- 3" to select AL 1 or AL 2 and press „CLEAR/
ALARM" 4 to confirm. Press „+ 2, - 3" to enter the
desired Hr/ Min values and press „CLEAR/ ALARM" 4
to confirm setting.
To view alarm time 1 and 2 (D), repeat press „CLEAR/
ALARM" 4 button at normal mode. Alarm time 1 or 2
(D) will display for 10 seconds and resume to normal
clock thereafter. To turn Alarm 1, 2 on and off, repeat
press „+" 2 button at normal mode. The unit will pro-
vide Daily Alarm which last for 1 minutes. At snooze
mode, the alarm will repeat 10 minutes.
SNOOZE
Press SNOOZE/LIGHT 8 to trigger snooze alarm. To
stop alarm for one day, press any keyon the unit.
MAX/ MIN MEMORY
Press the „MAX/ MIN" 5 to view the maximum valu-
es for 5 seconds, press 5 again to view the minimum
memory. To clear the memory record, press „CLEAR/
ALARM" 4 while the respective values displaying on
screen.
Temperature Trend Indicator (A): The 3 icons will in-
dicate Rising, Steady, Falling if the temperature change
is more than 1 degree in an hour.
TECHNICAL DATA
Power supply of main unit:
Battery type of main unit:
Temperature range of main unit:
Temperature tolerance of main unit:
Operating temperature:
Temperature display resolution:
Power supply of remote sensor:
Battery type of remote sensor:
Temp. Range of remote sensor (W044-3):
Temperature tolerance of remote sensor:
Transmission frequency:
Max. range (under opt. conditions):
Number of remote sensors:
313501.00_Manual_160630.indd 7
TEMPERATURE ALERT (available for desktop
models only)
Press „ALERT" 6 to turn temperature alert on and off.
Hold „ALERT"6 3 seconds to enter the alert setting
mode. The indoor channel and the Upper + Lower
pointers flash.
Press „+ 2, - 3" to select the indoor (C) or Ch1, 2,
3 and press „ALERT"6 to confirm the channel. The
Upper pointer and temperature will flash, enter the
desired upper limit with the „+ 2, - 3" buttons, press
„ALERT" 6 to confirm and go to the lower limit setting.
The Lower pointer and temperature will flash, enter
the desired lower limit with „+ 2, - 3" buttons, press
„ALERT" 6 to confirm and exit.
Each setting cycle will allow setting one channel
for the temperature alarm. The unit allows to enter
temperature alert for the indoor channel and all of the
Channel (B) 1, 2, 3. When temperature hits the limit of
the preset, the Upper & Lower pointers and the tem-
perature of the respective channel (B) will flash, Press
any keys to stop the alarm.
DISPOSAL OF WASTE ELECTRICAL AND
ELECTRONIC EQUIPMENT (WEEE):
Do not dispose of this product in your household
waste; hand in at a collection point for Waste Elec-
trical and Electronic Equipment. The symbol on the
product, in the instruction leaflet or on the packaging
indicates the correct manner of disposal.
DECLARATION OF CONFORMITY
We, Tegro AG (Ringstrasse 3, CH-8603 Schwerzen-
bach, Switzerland), hereby declare with sole respon-
sibility, that this product is in conformity with the
fundamental and other relevant standards of the Radio
Equipment 2014/53/EU. To request a copy of the
Declaration of Conformity, please email info@tegro.ch
2 x 1.5V
2 x AA / LR6 / AM3
-5 ºC to +50ºC
+/-1 ºC
0 ºC – 50 ºC
0.1 ºC
2 x 1.5V
2 x AAA / LR03 / AM4
–20 ºC to +60ºC
+/-1 ºC
433 MHz
30m
1
7 English
04.07.16 16:22