Replacing The Power Cable - Toolson PRO-DF 860 Mode D'emploi D'origine

Warning!
Before use, check that the guard hood reset sys-
tem works properly!
5.3 Setting the cutting angle and cutting
height (Fig. 4)
•
Undo the two screws for the angle adjustment
(2) and height adjustment (12).
•
Important! The set angle is indicated by the
arrow (b).
•
You can infinitely adjust the angle stop (10) to
the required angle between 0° and 90°.
•
Set the required height on the height scale
(a); the height of the groove should always be
in the center of the workpiece.
•
Now retighten the two screws.
•
A single pass will suffice for thin workpieces.
•
Several passes over the workpiece are requi-
red for thicker workpieces.
5.4 Changing the cutter (Figs. 5-6)
Danger! The plug must be disconnected from
the mains supply.
•
Remove the cover (a).
•
Place the face spanner (7) on the flange (b).
•
Press the locking knob; hold this knob and
turn the face spanner in the direction in which
the machine turns. After approximately half
a turn the locking knob will engage and the
flange can be released.
•
Release the cutter (c) from the flange (d).
•
Then pull the cutter (c) out of the base plate
(9).
•
Now fit the new cutter following the above in-
structions in reverse. Check that the direction
of rotation of the cutter is correct.
•
Refasten the cover (a).
Danger!
Never press the locking knob (8) when the motor
is running. Ensure that the cutter is perfectly secu-
re before you start work.
Note!
Do not use blunt or damaged saw disk cutters.
Anl_PRO_DF_860_SPK7.indb 16 Anl_PRO_DF_860_SPK7.indb 16
GB
6. Operation
6.1 ON/OFF switch (1)
•
To switch on the equipment slide the
switch(1) forwards and press the switch (1)
until it engages.
•
To switch off the machine push the switch (1);
it then returns to its original position.
6.2 Making a workpiece (Fig. 7)
Before you start work with the biscuit jointer, the
workpiece must be marked as follows.
•
Place the two parts side by side; the workpie-
ces must be securely clamped.
•
Draw a line with a pencil perpendicular to the
position of the joint.
•
Several joints will be required for large pieces
of wood.
•
The distance between two lines should be at
least 10 cm.
6.3 Positionin the biscuit jointer (Fig. 8)
•
Set and check the cutting depth.
•
Set the angle fence (10).
•
Set the height.
•
Position the machine near to the workpiece.
•
There are markings (a) on the machine; these
must line up with the line you have drawn.
•
Now switch on the machine and push the
drive motor (11) forwards. The workpiece
must be securely clamped.
6.4 Connecting the workpieces (Fig. 9/10)
•
When you have cut a slot on both workpieces
they can be connected.
•
Place glue in both slots.
•
Insert the biscuit dowel (a) into one of the
slots (Fig. 9).
•
Press both workpieces together (Fig. 10).
•
Clamp the workpieces and wait until the glue
has set.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 16 -
15.07.2016 07:40:00 15.07.2016 07:40:00