Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this case,
protect the machine by unplugging the
power cord.
Remove all loose clothing and confine
long hair.
Before operating the machine, remove
tie, rings, watches, other jewellery,
and roll up sleeves above the elbows.
Wear safety shoes; never wear leisure
shoes or sandals.
Always wear the approved working
outfit.
Do not wear gloves.
Wear goggles when working
Install the machine so that there is
sufficient space for safe operation and
workpiece handling.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be bolted
stable on firm and levelled table
surface or on the supplied cabinet
stand.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense. Do not operate
the machine when you are tired.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Keep children and visitors a safe
distance from the work area.
Do not operate the electric tool near
inflamm able liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Work only with well sharpened tools.
Machine only stock which rests
securely on the table.
Always close the chuck cover before
you start the machine.
Specifications regarding the maximum
or minimum size of the workpiece
must be observed.
Do not remove chips and workpiece
parts until the machine is at a
standstill.
Do not stand on the machine.
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn power cord
replaced immediately.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.
3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards
may still exist.
The rotating drill bit can cause injury.
Thrown workpieces and workpiece
parts can lead to injury.
Dust and noise can be health hazards.
Be sure to wear personal protection
gear such as safety goggles and dust
mask. Use a suitable dust collection
system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
4. Machine specifications
4.1 Technical data
Motor speed
Drill chuck capacity
Chisel capacity
Chisel bushings
5/8", 3/4", 13/16",
Head stroke
Fence size
Chisel centre to fence max
Table size
Table movement long-ways
Table movement cross-ways 100mm
Table tiltable
(model 719A only)
4
Maximum vertical distance
table to chisel bushing
Net weight 719A
Net weight 719AS
Mains
Output power
Reference current
Extension cord (H07RN-F):
Installation fuse protection
4.2 Noise emission
Acoustic pressure level (EN 11202):
Idling
In operation
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
As workplace conditions vary, this
information is intended to allow the
user to make a better estimation of the
hazards and risks involved only.
4.3 Content of delivery
Cabinet stand
13mm drill chuck
Chuck key
Spindle extension
5/8" (15,87mm) chisel bushing
3/4" (19.05mm) chisel bushing
13/16" (20,64mm) chisel bushing
1-3/16" (30,16mm) chisel bushing
2 handwheel handles
MDF table
Operating handle
work stop
Operating tools
Assembly kit
Operating manual
Spare parts list.
5. Transport and start up
5.1 Transport and installation
1450 rpm
The machine is designed to operate in
13mm
closed rooms and must be bolted on a
firm and levelled table surface or on
25 x 25mm
the original cabinet stand.
1-3/16"
200mm
5.2 Assembly
90 x 520mm
If you notice transport damage while
100mm
unpacking, notify your supplier
immediately. Do not operate the
180 x 520mm
machine!
400mm
Dispose of the packing in an
environmentally friendly manner.
35°
Clean all rust protected surfaces with
a mild solvent.
295mm
105 kg
116 kg
230V ~1/N/PE 50Hz
0,75 kW (1 HP) S1
5.5 A
3x1,5²
10A
67,8 dB (A)
77,5 dB (A)
Publicité
Table des Matières
