Klipsch RSA-500 Manuel Du Propriétaire page 4

RSA-500 SUBWOOFER AMPLIFIER
• Level Control – Play a variety of music recordings containing
strong but not overpowering bass. Adjust the RSA-500 level con-
trol until the music sounds consistently warm and natural. If you
have trouble getting enough low bass without the sound becom-
ing boomy, it probably means the Crossover control is set too
high. Try turning it down a bit at a time until the problem goes
away. If the sound is thin until you turn the subwoofer Level up so
much that lower bass is too prominent, start by changing the set-
ting of the Phase control. If that does not entirely solve the prob-
lem, you probably need to raise the Crossover frequency.
• Phase Control – In some installations the setting of the Phase
control may not make much difference, whereas in others it may
be necessary to go back and forth between the Phase
and Level controls for a while in order to get the very best blend
with the main speakers. Since each control setting (including the
one for crossover frequency in the receiver or processor) affects
the optimum settings for the others, it often takes a while to get
everything dialed in just right. Start with the Phase control at 0°
and play a recording with a prominent, repeating bass line in
your listening position. Repeat this process with the control in
the 180° position. Use the setting that yields the greatest
bass output.
General Comments About Adjustments: Since any change in
the setting of one control tends to change the optimum settings
for the others to some degree, the adjustment process is very
interactive and involves a great deal of trial and error. If after a
period of listening and calibration you are still not happy, it may
mean that you need to experiment a little with the location of the
subwoofer. That, of course, also interacts with everything else.
Again, patience is a virtue. The end result will be well worth the
effort.
ANALOG SURROUND RECEIVER / PROCESSOR OR
TWO-CHANNEL STEREO SYSTEM CONNECTION
Some analog A/V receivers and processors (without Dolby Digital
or DTS capability) have a line-level subwoofer output. Others
®
have left- and right-channel line-level outputs, as do some stereo
receivers and integrated amplifiers. All separate stereo preamps
and surround processors have line-level outputs. If your system is
built around one of these, it will almost always be best to use the
RSA-500's stereo line level inputs. This will allow use of the
crossover and level controls (Figure 4). You will need one or two
shielded, high quality interconnect cables of appropriate length
with RCA plugs on each end. Your dealer can help you select
suitable cables.
Figure 4
• Subwoofer Output – Connect the subwoofer output jack to
one or both of the line-level input jacks on the RSA-500.
• Preamp Outputs on Receiver or Integrated Amplifier – If
your receiver or integrated amplifier has spare preamplifier out-
puts for its front left and right channels and no subwoofer output,
connect these to the stereo line-level inputs on the RSA-500.
• Pre-out/Main-in Loops on Receiver or Integrated Amplifier
Some receivers and integrated amplifiers have their preamplifier
and power amplifier stages connected externally via jumpers. If
yours has its left and right front channels connected this way, you
can connect the RSA-500 to those preamp outputs. You will need
a pair of Y-adaptors, each with two male RCA plugs and one
female RCA jack. Remove the jumpers for the two channels. For
each, plug one leg of a Y-adaptor into the preamp output jack and
another into the main amp input jack. Plug the cables leading to
the RSA-500 into the female ends of the Y-adaptors.
• Separate Preamplifier or Surround Processor – You will
need a pair of Y-adaptors, each with one male RCA plug and two
female RCA jacks. Unplug the cables leading from the front left-
and right-channel outputs on the preamp or processor and plug
the Y-adaptors into them. For each channel, plug the cable lead-
ing to the power amplifier into one of the RCA jacks on the Y-
adaptor and the cable leading to the RSA-500 into the other.
• Crossover Adjustment – Set the control to the approximate
low-frequency limit of your main left and right front speakers. If
you don't have their specifications, take an educated guess
based on the size of the speakers. A large speaker will usually
work down to lower frequencies than a small speaker. So for a
large floorstanding loudspeaker, you might start with the
Crossover frequency set all the way down to 40Hz, whereas for
very small satellite speakers you might want to turn it all the way
up to 120Hz. Typical bookshelf speakers would tend to be in the
50Hz to 80Hz range. If the crossover frequency is set higher than
®
100Hz, the subwoofer should be in the front of the room
near the front main speakers.
• Level Control – Play a variety of music recordings containing
strong but not overpowering bass. Adjust the RSA-500 level con-
trol until the music sounds consistently warm and natural. If you
have trouble getting enough low bass without the sound becom-
ing boomy, it probably means the Crossover control is set too
high. Try turning it down a bit at a time until the problem goes
away. If the sound is thin until you turn the subwoofer Level up so
much that lower bass is too prominent, start by changing the set-
ting of the Phase control. If that does not entirely solve the prob-
lem, you probably need to raise the Crossover frequency.
• Phase Control – In some installations the setting of the Phase
control may not make much difference, whereas in others it may
be necessary to go back and forth between the Phase and Level
controls for a while in order to get the very best blend with the
main speakers. Since each control setting (including the one for
crossover frequency in the receiver or processor) affects the opti-
mum settings for the others, it often takes a while to get every-
thing dialed in just right. Start with the Phase control at 0° and