Technical Specifications - Stomer Professional SJS-750-QL Mode D'emploi

English
Jig saw
INTENDED USE
This tool is intended for making cut-throughs and cut-outs
in wood, plastic, metal, ceramic plates and rubber, and is
suitable for straight and curved cuts at 0° or 45°.

TECHNICAL SPECIFICATIONS

PRODUCT ELEMENTS
1. Switch for on/off
2. Button for switch locking
3. Wheel for adjusting sawing speed
4. Lever for selecting sawing mode
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, fi re
and/or serious injury.
● Always keep the cord away from moving parts of the
tool
● If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
● Never use tool when cord is damaged; have it replaced
by a qualifi ed person
● Do not cut material containing asbestos
● Do not use a saw blade which is cracked, deformed or
dull
● Keep hands away from the saw blade while the tool is
in use
● Remove all obstacles on top of as well as underneath
the cutting path before you start cutting
● Always disconnect plug from power source before
making any adjustment or changing any accessory
● Wear a dust protection mask when working with
materials which produce dust that is detrimental to
health; inform yourself beforehand about the materi-
als to be worked on
● Wear protective goggles when working with materials
which produce chips
● Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start cutting
● Check the functioning of the tool before each use and,
in case of a defect, have it repaired immediately by a
qualifi ed person; never open the tool yourself
● Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to a
220V supply)
1
2
● When used outdoors, connect the tool via a fault cur-
rent (FI) circuit breaker with a triggering current of 30 mA
maximum, and only use an extension cord which is in-
tended for outdoor use and equipped with a splash-proof
coupling-socket
● The noise level when working can exceed 85 dB(A);
wear ear protection
● When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
● SBM Group can assure fl awless functioning of the tool
only when original accessories are used
● Use completely unrolled and safe extension cords with
a capacity of 16Amps (U.K. 13 Amps)
● In case of electrical or mechanical malfunction, imme-
diately switch off the tool and disconnect the plug
● This tool should not be used by people under the age
of 16 years
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
● Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the plug
● If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
Your machine is double insulated in
accordance with EN 50144; therefore no
earthwire is required.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
Lubricate the saw blade guide regularly.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of the
packaging materials can be recycled. Take these materi-
als to the appropriate recycling locations. Take your un-
wanted machines to your local SBM Group dealer. Here
they will be disposed of in an environmentally safe way.
6