Télécharger Imprimer la page

EINHELL TH-MS 2112 T Mode D'emploi D'origine page 19

Masquer les pouces Voir aussi pour TH-MS 2112 T:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 20
Anleitung_TH_MS_2112_T_SPK1__ 03.05.13 07:58 Seite 19
Move the machine head to its upper position.
n
Fasten the turntable (8) in 0° position.
n
Undo the tightening screw (22) and use the
n
handle (2) to tilt the machine head to the left until
the pointer (b) coincides with the required angle
value.
Retighten the tightening screw (22) and make
n
the cut as described in section 7.2.2.
7.2.5 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 11/12/13)
The crosscut and miter saw with table can be used to
make miter cuts to the left of 0°- 45° in relation to the
work face and, at the same time, 0° - 45° in relation
to the stop rail (double miter cut).
Move the machine head to its upper position.
n
Release the turntable (8) by slackening the
n
locking screw (10).
Use the handle (2) to adjust the turntable (8) to
n
the angle required (in this connection see also
section 7.2.3).
Retighten the locking screw (10) in order to
n
secure the turntable in place.
Undo the tightening screw (22) and use the
n
handle (2) to tilt the machine head (4) to the left
until it coincides with the required angle value (in
this connection see also point 7.2.4).
Screw the tightening screw (22) back down
n
again.
Cut as described under section 7.2.2.
n
8. Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
n
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
n
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
n
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
9.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.
9.3 Maintenance
There are no parts inside the equipment which
n
require additional maintenance.
Lubricate all moving parts at regular intervals.
n
9.4 Ordering replacement parts
Please quote the following data when ordering
replacement parts:
Type of machine
n
Article number of the machine
n
Identification number of the machine
n
Replacement part number of the part required
n
For our latest prices and information please go to
www.isc-gmbh.info
10. Disposal and recycling
The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
GB
19

Publicité

loading

Ce manuel est également adapté pour:

43.003.17