Noise/Vibration Information; English - Wurth Master MH 16-XE Instructions D'emploi

OBJ_DOKU-8617-001.fm Page 10 Friday, October 19, 2007 10:46 AM
Technical Data
Demolition Hammer
Art. No.
Rated power input
Impact rate
Impact energy per stroke
Tool holder
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given apply for nominal voltages [U] of
230/240 V.
Starting cycles generate brief voltage drops. Interference
with other equipment/machines may occur in case of unfa-
vourable mains system conditions. Malfunctions are not to
be expected for system impedances below 0.25 ohm.

Noise/Vibration Information

Measured values determined
2000/14/EG and EN 60745.
Typically the A-weighted noise levels of the product
are: Sound pressure level 92 dB(A); Sound power
level 103 dB(A). Uncertainty K =2 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Chiselling: Vibration emission value a
2
Uncertainty K=2 m/s .
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is
used for different applications, with different acces-
sories or poorly maintained, the vibration emission
may differ. This may significantly increase the expo-
sure level over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the
exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as: main-
tain the tool and the accessories, keep the hands
warm, organisation of work patterns.
10–English
We declare under our sole responsibility that the
MH 16-XE
product described under "Technical Data" is in con-
0702 575 X
formity with the following standards or standardiza-
W 1750
tion documents: EN 60745 according to the
bpm 1300
provisions
J 45
98/37/EC (until 28 Dec 2009), 2006/42/EC (from
mm 30 29 Dec 2009), 2000/14/EC.
2000/14/EC: The guaranteed sound power level
L is lower than 105 dB(A). Conformity assessment
kg 16.5
WA
procedure according to Annex VI.
/II
Notified body:
TÜV NORD CERT GmbH & Co. KG,
Am TÜV 1, 30519 Hannover
Technical file at:
Adolf Würth GmbH & Co.KG, PFW,
D-74650 Künzelsau
Künzelsau, 19.06.2007
07
according to
Adolf Würth GmbH & Co. KG
P. Zürn
2
=10 m/s ,
h
The carrying handle 3 can be turned to any position.
Loosen the knurled nut 4, turn the carrying handle 3
around the machine axis to the desired position and
tighten the knurled nut 4 again.
The carrying handle 3 can also be mounted facing
to the other side. Completely unscrew the knurled
nut 4 and then pull out the hexagon bolt upward.
Pull off the carrying handle 3 to the side and tilt the
remaining clamping element by 180°. Mount the
carrying handle 3 in reverse order.
Declaration of Conformity
of the directives
R. Bauer
Carrying Handle
1 619 929 790 • 19.10.07
2004/108/EC,