Transportation, Storage And Disposal - Jonsered LM 2146 CMD Manuel D'utilisation

a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
• If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, refer to
on page 15 . (Fig. 49)
• Replace the spark plug if it is necessary.
To examine the fuel system
• Examine the fuel tank cap and the seal for the fuel
tank cap to make sure that there are no damages.
• Examine the fuel hose to make sure that there are
no leaks. If the fuel hose is damaged, let a service
agent replace it.
To adjust the clutch wire (LM 2146
CMD)
If the drive feels slow, it is necessary to adjust the clutch
wire.
1. Attach the clutch wire in different holes on the drive
bail to adjust the length of the clutch wire. Decrease
the length of the clutch wire to increase the drive
speed. Extend the clutch wire to decrease the drive
speed. (Fig. 50)
Note: If the drive is engaged when you do not pull
the drive bail, it is necessary to extend the clutch
wire.
Transportation and storage
• Remove the battery from the product before storage.
• For storage and transportation of the product and
fuel, make sure that there are no leaks or fumes.
Sparks or open flames, for example from electrical
devices or boilers, can start a fire.
• Always use approved containers for storage and
transportation of fuel.
• Empty the fuel tank before you put the product in
storage for a long period of time. Discard the fuel at
an applicable disposal location
• Obey the special requirement on package and labels
for commercial transports, including by third parties
and forwarding agents.
• Consult an expert in dangerous material before
shipping the product. Obey all applicable national
regulations.
• Use tape on open terminals when you put the battery
in a package. Put the battery in the package tightly
to prevent movement.
• Safely attach the product during transportation to
prevent damage and accidents.
• Keep the battery away from the battery charger
during storage.
14
Technical data

Transportation, storage and disposal

2. For small adjustment of the drive speed, turn the
adjuster screw. To increase the drive speed, turn the
adjuster screw counterclockwise. To decrease the
drive speed, turn the adjustment screw clockwise.
(Fig. 51)
If the drive feels slow also after the adjustment, let an
approved service agent replace the drive belt.
To adjust the clutch wire (LM 2146
CMDA, LM 2146 CMDAE, LM 2146
CMDAH)
If the drive feels slow, it is necessary to adjust the clutch
wire.
1. To increase the drive speed, turn the adjuster screw
counterclockwise.
Note: If the drive is engaged when you do not pull
the drive bail, it is necessary to extend the clutch
wire.
2. To extend the clutch wire and decrease the drive
speed, turn the adjustment screw clockwise. (Fig.
52)
If the drive feels slow also after the adjustment, let an
approved service agent replace the drive belt.
• Keep the product in a locked area to prevent access
for children or persons that are not approved.
• Keep the product in a dry and frost free area.
• Do not keep the battery in an area where static
electricity can occur. Do not keep the battery in a
metal box.
Disposal
• Obey the local recycling requirements and applicable
regulations.
• Discard all chemicals, such as engine oil or fuel, at a
service center or at an applicable disposal location.
• When the product is no longer in use, send it to a
Jonsered dealer or discard it at a recycling location.
Disposal of the battery and battery
charger
Symbols on the product or its packaging indicate that
this product cannot be handled as domestic waste. It
must instead be submitted to an appropriate recycling
station for the recovery of electrical and electronic
equipment.
By ensuring that this product is taken care of correctly,
you can help to counteract the potential negative impact
868 - 003 - 23.10.2018