Human Solution pro-line II 39200 Instructions De Montage

ÉTAPE 1 ÉTAPE 2
3
1
2
ÉTAPE 4 ÉTAPE 5
7L
7R
8
6
5
10
8
8
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vérifier les quantités des pièces.
ÉTAPE 1 Insérer les cinq roulettes (2) dans la base (1). Pousser fermement jusqu'à ce que les roulettes (2) s'encliquettent. Insérer le Vérin
pneumatique (3) dans la Base (1)
ÉTAPE 2 Fixer le plaque du siège (4) au coussin du siège (5) avec la flèche vers l'avant de la chaise à l'aide de quatre vis longues (9). SERREZ
TOUTES LES VIS AVEC LA CLÉ ALLEN (11).
ÉTAPE 3 Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas
ÉTAPE 4 Fixez les Bras (7L et 7R) au coussin du siège (5) avec deux vis courtes (8) pour chaque bras (7). NE PAS SERRER LES VIS.
ÉTAPE 5 Fixez les Bras (7L et 7R) au coussin du dossier (6) avec deux vis courtes (8) pour chaque bras (7). APPLIQUER
PRESSION FIRME POUR ALIGNER ET SERRER ENTIÈREMENT TOUTES LES VIS EN UTILISANT LA CLÈ ALLEN (11). Couvrir les trous
des Bras (7L et 7R) avec quatre Bouchons en plastique (10) pour chaque Bras (7).
ATTENTION: AVANT D'UTILISER LE FAUTEUIL, S'ASSURER D'AVOIR SERRÉ COMPLÈTEMENT TOUTES LES VIS.
39200 / 39202 / 39203
FAUTEUIL BIG & TALL DELUXE
À HAUT DOSSIER
INSTRUCTIONS DE MONTAGE
ÉTAPE 3
9
4
5
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Roulettes . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3. Vérin pneumatique . . . . . . . . . . . . . . . . . . .1
4. Plaque du siège . . . . . . . . . . . . . . . . . . . . .1
7L
7R
8 10
5. Coussin du siège . . . . . . . . . . . . . . . . . . . .1
6. Dossier . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
7. Bras (7L et 7R) . . . . . . . . . . . . . . . . . . . . . .2
8. Vis courtes . . . . . . . . . . . . . . . . . . . . . . . . .8
9. Vis longues . . . . . . . . . . . . . . . . . . . . . . . . .4
10. Bouchons en plastique . . . . . . . . . . . . . . .8
11. Clé allen (non montré) . . . . . . . . . . . . . . .1
3
3
1
QTÉ
PROLINE II LIMITED WARRANTY
ProLine II chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization.
At it's option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on components
still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 400 lbs.
or less. The 54666 is for persons weighing 300 lbs. or less. The 7103M, 7602R, 7605R, 7600R, 81108, 81308 & 81608 are for persons weighing 400 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five
year warranty on all parts applies. Fabric is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
All ProLine II chairs meet or exceed ANSI BIFMA standards.
It is the customer's responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty
will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
© Office Star Products mai 2015
39200 / 39202 / 39203
BIG & TALL DELUXE HIGH BACK CHAIR
OPERATING INSTRUCTIONS
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1).
To lower seat height sit on chair and lift lever (1).
NOTE: It is normal for chair to slightly lower under body weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an
adjustment that will allow the user to change the tension of
the tilting feature. Turn knob (2) clockwise to increase tension
and counter-clockwise to decrease or ease the tension. To lock
return chair to the upright position and push lever (1) in. To
unlock pull lever (1) out.
NOTE: Be careful not to loosen the back tilt adjustment knob
completely.
ARM HEIGHT ADJUSTMENT
To adjust Arm Height, push button (3) to allow the arms to move
up or down freely, release button (3) once desired height is
reached.
• ARM FLIP UP AND DOWN
To flip arms up, simply pull up on arm. To lower arm, simply pull
down on arm.
2
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts screws and knobs are tight every three
months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover
as head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.