Monacor PA-1200R Mode D'emploi page 6

Please unfold page 3. Then you can always see the
GB
operating elements and connections described.
1 Operating Elements and Connections
1 Display
2 FM/AM button for switching between the frequency
ranges FM1 (6 FM memory stations), FM2 (6 FM
memory stations) and AM (6 AM memory stations)
3 Button ON for switching the tuner on and off
4 Buttons and
Pressing the buttons shortly: manual tuning
Pressing the buttons for approx. 2 seconds: auto-
matic tuning
5 Numerical keys for selecting the station memories
6 Volume control (mixing control)
2 Safety Notes
The insertion module corresponds to all required
directives of the EU and is therefore marked with
The insertion must be installed by skilled personnel
only.
The insertion is suitable for indoor use only. Protect
it against dripping water and splash water, high air
humidity, and heat (admissible ambient temperature
range 0 – 40 °C).
Do not operate the unit and the installed insertion or
immediately disconnect the plug from the mains
socket
1. if there is visible damage to the insertion, the unit,
or the mains cable,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the insertion or the entire unit must be
repaired by skilled personnel.
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
No guarantee claims for the insertion and no liability
for any resulting personal damage or material dam-
age will be accepted if the insertion is used for other
purposes than originally intended, if it is not correctly
installed, operated, or not repaired in an expert way.
If the insertion is to be put out of operation
definitively, take it to a local recycling plant for
a disposal which is not harmful to the envi-
ronment.
6
for adjusting a station
3 Applications
The insertion is suitable for installation in the following
MONACOR units and must be installed in these units
by skilled personnel only.
PA-1120 PA amplifier for 5 zones
PA-1200 PA amplifier for 4 zones
PA-1200EX basic unit for 2 insertions
PA-1204EX basic unit for 4 insertions
PA-1240 PA amplifier for 5 zones
PA-5240 PA amplifier for 5 zones
PA-5480 PA amplifier for 5 zones
PA-6240 PA amplifier for 6 zones
PA-6480 PA amplifier for 6 zones
PA-6600 PA amplifier for 6 zones
4 Installation into the PA Amplifier
WARNING
Prior to the installation of the insertion
disconnect the mains plug of the ampli-
fier or basic unit of the insertion. Other-
wise there is an electric shock hazard.
.
1) Remove the cover of the amplifier.
2) Screw off the blank panel of the insertion slot at the
amplifier. Remove the three-pole line glued to the
blank panel and connect it to the pin jack CON 1 of
the tuner after the AM/FM tuner has been inserted
and tightened with screws (see fig. 2).
3) Unscrew the blank panel at the back of the amplifier
and remove it. Insert the supplied PCB with the
antenna screw connections and fasten it with
screws.
4) Insert the 4-pole line of the inserted PCB to the pin
socket CON 3 of the AM/FM tuner.
5) Only for the amplifier PA-1200: Plug the 2-pole line
of the connection AN 08 of the terminals M.O.H. into
the pin jack CON 2 of the AM/FM tuners.
6) The insertion PA-1200R has a storage battery
(position BAT 1) to store the station tunings. This
storage battery is deactivated ex factory to prevent
a gradual discharge prior to the installation. For the
operation activate the battery: Set the switch SW 2
to the position showing the marking on the sliding
switch (fig. 2). As the switch can also be installed by
turning it around 180°, observe this marking in any
case.
For deactivating the battery for a longer time
(e. g. for storage), set the switch so that the marking
cannot be seen.