Muse MT-100 BR Mode D'emploi page 4

GB TURNTABLE STEREO SYSTEM
LOCATION AND DESCRIPTION CONTROLS
1. PLATTER
2. SPINDLE
3. 45 RPM ADAPTOR
4. TONE ARM
5. LIFT LEVER
6. DC IN 5V JACK
7. EXTERNAL DEVICE OUTPUT JACK
8. USB PORT
9. REC / : RECORD/ PLAY/PAUSE BUTTON
10. NEXT BUTTON
11. BACK BUTTON
12. MODE BUTTON (TO SELECT PHONO, USB, AUX IN
MODE)
13. AUX IN JACK
14. POWER ON/ OFF AND VOLUME CONTROL (MIN/
MAX)
15. PHONES JACK
16. MODE INDICATOR
17. CARTRIDGE WITH STYLUS
18. TONE ARM REST
19. AUTO STOP (ON/OFF) SWITCH
20. SPEED SELECTOR (33/45/78)
21. PHONOGRAPH LID
22. SPEAKERS
23. CARRYING HANDLE
24. LATCH
POWER SUPPLY
Using the AC adaptor
AC adaptor:
Input 100-240V 50/60Hz 0.5A
Output 5V , 1000mA
The supplied AC adaptor is suitable for use on AC main supplies of 100-240V
mains supply within these parameters.
Caution:
* The included AC adapter is exclusively intended to be used with this device
* Turn off the power before unplugging the AC adapter to avoid damaging the device.
* In case of unused for long periods, unplug the AC adapter from the outlet.
* Place the unit near the outlet and make sure it is easily accessible. If a malfunction occurs, immediately disconnect the
unit from the wall outlet.
HXT-3812 IB MUSE 001 REV0.indd 4
AC and should only be connected to a
EN - 1
* The adapter enables you to unplug the unit. It must be easily accessible during use.
* To completely turn off power, unplug the adapter from the wall outlet.
* Never use a damaged power adapter. Place the power cord safely and so that you do not pinch or crush it. If the cable
is damaged, contact a repair service.
TURN ON/ OFF THE UNIT
1. To turn the unit on, rotate the POWER ON/OFF switch clockwise until a "click" is heard and set the volume (MIN/MAX)
to a lower level.
2. When you have finished the unit, rotate the POWER ON/OFF switch counter-clockwise until a "click" is heard to turn off
the unit.
LISTEN TO THE PHONO
1. When the unit is on, press MODE button to select the phono mode until function indicator light becomes RED.
2. Remove the stylus cover from the stylus and have released the Tone arm rest.
3. Place a record on the turntable platter and select the desired speed (33/45/78) according to the record.
NOTE: If you are playing 45RPM singles, place the 45 RPM adapter on the center spindle.
4. Push up the lift lever to raise the tone arm and gently move the tone arm to the desired position onto the record, Push
down the lift lever, the tone arm slowly onto the record to start playing the record.
5. Adjust the volume control (MIN/MAX) to your desired level.
6. If the AUTO STOP ON/OFF Switch turned ON, the record will stop automatically when finished (For some few vinyl
records, it will not stop when it does not come to the end.). If Auto Stop switch turned OFF, record will NOT stop
automatically when finished.
IMPORTANT:
Do not turn or stop the Turntable platter manually. Moving or jarring the Turntable platter without securing the Tone Arm
Clamp could result in damage to the Tone Arm or Stylus.
USING THE AUX IN MODE
1. Connect one end of the cable (not supplied) to the auxiliary input connector of the unit(cable not supplied).
2. When the unit is on, Repeatedly press MODE button to select AUX IN mode until indicator becomes blue and red
flashing alternately. Normally use your external audio appliance, the sound automatically goes through the speakers of
your device.
3. Adjust the volume (MIN/MAX) to the desired level.
4. Disconnect the external appliance from the auxiliary input to stop playback.
LISTEN TO THE DEVICE USB
1. Connect a USB device containing MP3 files or MP3 player to the USB port.
2. When the unit is on, Repeatedly press MODE button to select the USB mode until indicator becomes PURPLE flashing.
The USB start to playback automatically. Press to pause, the indicator keep remain purple without flashing.
3. Adjust the volume (MIN/MAX) to the desired level.
4. Press to skip forward to the next track or repeatedly to several tracks. Press
or press repeatedly to skip backwards several tracks.
5. Press to pause the USB playback.
Remark: When is USB device is plugged into the turntable player, the mode change order is phono
Aux in.
When is USB device is not plugged into the turntable player, the mode change order is phono
Removing the USB device
Please be sure to stop playback and turn the unit OFF before removing the USB device to avoid damage the USB and
system.
return to the beginning of the track,
USB playback
Aux in.
EN - 2
2016/7/21 17:27:22