ROBBE 8734 Manuel D'utilisation page 5

M o d e l l s p o r t
S A F E T Y I N S T R U C T I O N S F O R C O N T R O L L E R S
• Observe the technical data of the controller.
• Observe the polarity of all connection cables.
• Avoid short circuits at all costs.
• Install or package the regulator so that it cannot come into contact with grease, oil or water.
• Effective interference suppression measures on the electric motor with, for example, interference sup-
pression capacitors
• Ensure adequate air circulation.
• Never reach into the turning circle of the propeller during start-up Risk of injury
Dealing with model aircraft and vehicles requires technical understanding and a high level of safety
awareness. Incorrect assembly, incorrect adjustment, improper use or the like can lead to personal injury
or damage to property. Sudden starting of connected motors can lead to injuries due to rotating parts
such as propellers. Always stay away from these rotating parts when the power source is connected. All
drive components should be safely and securely mounted during a function test. Use is only permitted
within the scope of the technical specification and only for RC hobby applications. Before use, check
that the speed controller is compatible with your drive motor or power source. Never operate the speed
controller (correct speed controller) with external power supply units. Speed controllers should always be
protected from dust, moisture, vibration and other mechanical stresses. Even splash-proof or waterproof
equipment should not be permanently exposed to moisture or moisture. High operating temperatures
or poor cooling should be avoided. The recommended temperature range should be approximately
between -5°C and +50°C. Ensure proper connection and do not cause reverse polarity which would per-
manently damage the speed controller. Never disconnect the device from the motor or battery during
operation. Use high-quality plug systems with sufficient load capacity. Avoid strong bending or tensile
stress on the connecting cables. After termination of flight or driving operation, disconnect the battery
to prevent deep discharge of the battery. This would cause permanent damage. For the BEC version of
the controller, check that the BEC power of the device is sufficient for the servos used. Speed controllers
should be installed as far away as possible from other remote control components. We recommend
carrying out a range test before operation. We recommend regular checking of the controller for func-
tion and externally visible damage. Do not continue operating the controller if you notice any damage.
The connection cables must not be extended. This can lead to unwanted malfunctions. Despite existing
safety and protective devices of the device, damage may occur which is not covered by warranty. The
warranty also expires if changes are made to the device.
Important information:
The receiver system is powered by the built-in BEC system of the controller.
For commissioning, always move the throttle stick to the „Motor off" position and switch on the trans-
mitter. Only then connect the battery. To switch off always disconnect the connection battery motor
controller, first then turn off the transmitter. During the functional test, move the servos of the rudders to
neutral position with the remote control (stick and trimming lever on the transmitter to the middle positi-
on). Please make sure to leave the throttle stick in the lowest position so that the engine does not start.
For all work on to the parts of the remote control, motor or controller, follow the instructions supplied with
the units. Also read the instructions of the battery and the charger carefully before commissioning.
Check the engine mounting bolts in the fuselage regularly for tightness.
www.robbe.com
U S E R M A N U A L
Our articles are equipped with the legally required 24 months warranty. Should you wish to assert a
justified warranty claim, always contact your dealer, who is responsible for the warranty and the proces-
sing. During this time, any functional defects that may occur, as well as manufacturing or other problems,
will be rectified. Material defects corrected by us free of charge. Further claims, e.g. for consequential
damages, are excluded. The transport to us must be free, the return transport to you is also free. Freight
collect shipments cannot be accepted. We cannot accept liability for transport damage and loss of
your consignment. We recommend appropriate insurance.
To process your warranty claims, the following requirements must be met:
• Attach the proof of purchase (receipt) to your shipment.
• The units have been operated in accordance with the operating instructions.
• Only recommended power sources and original robbe accessories have been used.
• There is no moisture damage, external interference, reverse polarity, overloading or mechanical da-
mage.
• Attach relevant information for finding the fault or defect.
Robbe Modellsport cannot monitor compliance with the assembly and operating instructions or the
conditions and methods for installation, operation, use and maintenance of the model components.
Therefore, we accept no liability for losses, damage or costs arising from or in any way connected with
incorrect use and operation.To the extent permitted by law, the obligation to pay damages, irrespective
of the legal grounds, shall be limited directly to the invoice value of the claims arising from the event
causing the damage.
Made in China
Ro-Control PRO WIFI MODUL NO. 8734
W A R R A N T Y
D I S C L A I M E R
C O N F O R M I T Y
Robbe Modellsport hereby declares that this device complies with the essential
requirements and other relevant regulations of the corresponding CE directives. The
original declaration of conformity can be found on the Internet at www.robbe.com,
in the detailed product view of the respective device description or on request. This
product can be operated in all EU countries.
D I S P O S A L
This symbol means that small electrical and electronic devices must be disposed of at
the end of their useful life, separated from the household refuse. Dispose of the device
at your local municipal collection point or recycling centre. This applies to all coun-
tries of the European Union and other European countries with a separate collection
system.
+14
E N G L I S H 5