Hood Description - arietta ALZ430SSA Guide D'instructions

WARNING: Electrical Shock Hazard
Electrically ground blower.
Connect ground wire to green and yellow ground wire in
terminal box. Failure to do so can result in death or electrical
shock.
7.
Connect green (or bare) ground wire from home power
supply to yellow-green ground wire (F) in terminal box using
UL listed wire connectors.
8. Tighten strain relief screw.
9.
Install terminal box cover.
10.
Reconnect power.

Hood Description

A
B
A. Blower and light controls
B. LED Lamps housings
C. Grease filter Handle
E. Grease filter
Range Hood Controls
A B
A. Timer button
B. Light button
C. Display
Timer Button
• The default timer setting is 10 minutes, and it can be adjusted
between 20 minutes and 1 minute.
• After pressing the timer key, the control enters to a timer se
up mode, and user can adjust the timer countdown time with
the "-" and "+" keys within 5 seconds. The timer can be
initiated immediately pressing the timer key, after setting the
timer duration or pressing the timer key twice (default 10
minutes setting).
• If not action occurs within 5 seconds the countdown will start.
• During the timer setup the "-" and "+" keys are dedicated to
the timer and no motor action will occur.
• Once initiated the timer, it can be cancelled by pressing the
timer key again
E
D
C D E
D. - button
E. + button
Light Key
• Press lamp key to turn ON the light (Lamp state previously
OFF).
• Press lamp key to turn OFF the light (Lamp state previously
ON).
Display
Shows the hood settings.
"-" Key. Speed Decrease / OFF
• This key is used to decrease the fan speed, or turn OFF the
fan.
• The fan will turn OFF if the "-" key is pressed and the hood
was in the first speed.
• If the fan is at second speed and the "-" key is pressed, the
fan will be set to first speed.
• If the fan is at third speed and the "-" key is pressed, the fan
will be set to second speed.
• If the fan is OFF and the "-" key is pressed, the control
backlight will light up.
"+" Key. Speed Increase / ON
• This key is used to increase the fan speed, or turn ON the fan.
• The fan will turn ON if the "+" key is pressed and the hood
was OFF.
• If the fan is at first speed and the "+" key is pressed, the fan
will be set to second speed.
• If the fan is at second speed and the "+" key is pressed, the
fan will be set to third speed.
• If the fan is at third speed and the "+" key is pressed, a beep
will sound.
Special functions
Clock programming
• The clock can be reprogrammed at any time except during an
active timed function.
• The clock can be displayed in a twelve hour format and valid
clock times are from 1:00 to 12:59.
• The clock can be reprogrammed pressing the "Timer" key for
5 seconds, and after, the clock can be adjusted with the "+"
and "-" keys. Colon ":" will flash indicating clock programming
mode.
• The user can have minute increments / decrements of 1
minute, but if the user keep pressing the "+"/"-" keys for more
than 1 second, the increments / decrements will be of 5
minutes. During this option the control will round to the
nearest 5 minutes.
• The user can finish on reprogramming the clock pressing the
"timer" key.
• After 1 minute of no key pressed the control will accept the
programmed clock time and will add one minute to the set
clock.
Grease filter saturation alarm
• After thirty fan functional hours, the display will show "Grease
Filter" if the fan is active. When this icon is shown in the
display, the grease filters installed are required to be washed.
• To reset the grease filter saturation alarm the user must press
the "+" key for 5 seconds, after this action the icon "grease
9