MF Lono Mode D'emploi page 10

Slow Cooking
1. Fill the Slow Cook insert (2) with the desired food. In order to retain cooking fl avours, the food
should be quickly fried fi rst.
2. Place the water tank (4) on the main appliance (5).
Note: The appliance will not work without the water tank.
3. Then fi ll the water tank with clean water at least to the
the MAX marking "Slow Cook" on the back of the water tank.
Note: the water level around the Slow Cook insert should correspond to the fi ll level inside the
Slow Cook insert in order to ensure optimum heat transfer to the food being cooked.
⋅
Low fi ll level in Slow Cook insert = water to
⋅
Medium fi ll level in Slow Cook insert = water between
markings.
⋅
Maximum fi ll level in Slow Cook insert = water to
⋅ Caution! Do not fi ll beyond the
water being forced up into the Slow Cook insert.
4. Then insert the Slow Cook insert into the water tank. Top up with a little water if required.
You can now slow cook using a pre-set custom cooking time or individually programmed
temperature and cooking time settings. Proceed as described in the section on "Sous Vide
cooking" in steps 4 to 9.
Note: When you remove the water tank from the device after use, a small residual amount of
water will spill from the pump onto the top of the main appliance. This is normal. Remove the
mains plug and empty the main appliance into the sink.
Setting the temperature unit (°C/°F) and water hardness
1. Place the water tank (4) on the main appliance (5).
2. Connect the appliance to the mains. The appliance is now in standby mode. Press the settings
button (9) and hold it down for at least 3 seconds. If the appliance is already in standby mode,
press the settings button (9) and hold it down for at least 3 seconds.
3. The °C icon fl ashes. By twisting the selector knob (12), you can change the setting to °F. In this
case, the preset temperature of 60°C is replaced with 140°F. Confi rm your selection by pressing the
selector knob again.
4. Instead of the time, the preset water hardness H4 now fl ashes on the display. By twisting the
selector knob, you can adjust this to H1 to H4 according to the water hardness where you live.
Note: You can fi nd out your water hardness from your council or from your energy and water
provider or online.
5. Once you have confi rmed the water hardness set, it is permanently saved in the device.
6. Then press the on/off button (7) to put the appliance into standby mode.
Hardness range Hardness
1 Soft 0 – 7° dH
2 Medium >7 – 14° dH
3 Hard >14 – 21° dH
4 Very hard > 21° dH
18
MIN marking and no higher than
MIN marking
MIN and MAX
MAX marking
MAX marking "Slow Cook" as this could lead to
Cleaning and care
Cleaning
Pull out the mains plug and allow the appliance to cool down.
Do not immerse the appliance in water, the surfaces can be cleaned using a damp cloth and a little
washing-up liquid. Do not use any sharp or abrasive cleaning agents.
Dishwasher-safe
Glass lid (1)
Slow Cook insert (2)
Adjustable meat and vegetable
holder (3)
Water tank (4)
Main appliance (5)
Scale indicator
Limescale deposits increase the time it takes the Sous Vide Cooker to heat up. They also lead to energy
losses and impair the service life of the appliance.
The automatic scaling indicator determines the time for the next descaling cycle. Depending on the
level of use and hardness level of the water, you are prompted to run a descaling process by the fact
that the descaling light is permanently lit.
Descaling agent
Use a commercially available descaling agent that is also suitable for fi lter coffee machines. Use a commercially available descaling agent that is also suitable for fi lter coffee machines.
Do not use regular or concentrated vinegar because this may damage the materials in the
appliance. appliance.
Use of descaling agents based on citric acid may lead to the formation of precipitates that seal the
limescale layer or clog up the lines in the appliance. Descaling with citric acid also takes too long, as a
result of which complete descaling cannot be guaranteed. result of which complete descaling cannot be guaranteed.
Our warranty does not cover damage caused by using unsuitable descaling agents or failure to
follow the descaling instructions. follow the descaling instructions.
Handle descaling agents carefully to prevent damaging furniture or clothing.
Can be rinsed Wipe off with a
under running damp cloth
water
19