SBS B770 Mode D'emploi page 2

G G B B
Thank you for choosing the SBS B770
Bluetooth earpiece. Before using it for the first
time, follow the instructions printed below.
A A - - V V O O L L U U M M E E ( ( + + ) )
B B - - V V O O L L U U M M E E ( ( - - ) )
C C H H A A R R G G I I N N G G T T H H E E B B A A T T T T E E R R Y Y O O F F T T H H E E E E A A R R P P I I E E C C E E
The earpiece uses a battery with high
performance "Lithium Polymer" technology.
The first time you use the earpiece, the battery
inside may not be charged and it will be
necessary to charge it up.
R R e e c c h h a a r r g g e e . . Connect the battery recharger to
the electric socket and to the earpiece. The
red light will come on and the recharging
process will begin. When the battery has been
recharged the light will go off. It will take
about two hours to fully recharge the battery.
B B a a t t t t e e r r y y d d e e a a d d . . When the B770 battery has
almost run down, the light will flash red and a
beep will be heard in the earpiece.
N N O O T T E E : : to extend the life of the battery, we
recommend that you leave the B770 switched
off while recharging and only recharge it
when it is dead. If the B770 has not been used
for some time, it may take a few minutes for
the red light to come on.
S S t t a a t t u u s s
Stand-by
"Find me" mode
Calling
Battery dead
Recharge
C C - - P P O O W W E E R R A A N N D D
M M U U T T E E B B U U T T T T O O N N
D D - - A A N N S S W W E E R R A A N N D D E E N N D D
L L E E D D
Flashing BLUE
Flashing RED/BLUE
Quick flashing BLUE
Slow flashing RED
Fixed RED
S S W W I I T T C C H H I I N N G G O O N N , , C C O O N N N N E E C C T T I I N N G G A A N N D D
S S W W I I T T C C H H I I N N G G O O F F F F T T H H E E E E A A R R P P I I E E C C E E
S S w w i i t t c c h h i i n n g g o o n n . .
Press the C button and keep it pressed until
the blue light flashes three times (about 3
seconds). The B770 will switch to stand by.
C C o o n n n n e e c c t t i i n n g g . . After switching on the B770,
briefly press the D button to connect the
B B U U T T T T O O N N
earpiece to the last device with which it has
been associated (only after making the
L L E E D D
association).
S S w w i i t t c c h h i i n n g g o o f f f f . . Press the C button and keep it
pressed until the red light flashes three times
(about 3 seconds).
A A S S S S O O C C I I A A T T I I O O N N O O F F T T H H E E E E A A R R P P I I E E C C E E W W I I T T H H A A
B B L L U U E E T T O O O O T T H H D D E E V V I I C C E E
Before using the Bluetooth headset, you must
associate it with the device you are going to
use it with (telephone/PC).
A A S S S S O O C C I I A A T T I I O O N N
• Ensure that the B770 is switched off. Press
the C button and keep it pressed until the
light starts flashing red/blue (about 6
seconds), in this way the earpiece is ready
to be picked up by other devices ( "find me"
mode).
• Run the search for new Bluetooth
accessories from your device (phone/PC)* * .
At the end of the search the name of our
earpiece will appear on the display (the
name may vary from device to device).
• Select the B770 and, when requested to do
so, enter the PIN 1234, then press "OK" .
• The phone/PC will tell you that the new
bluetooth device has been associated, while
the B770 light will flash blue ( stand-by ).
N N O O T T E E : : With some phones it might be
necessary to authorise connection
from the phone.
* * To make the association, follow the
instructions in the user manual supplied
with the phone or with the PC Bluetooth
interface. The B770 will stay in "find me"
B B 7 7 7 7 0 0