Publicité
Les langues disponibles
Les langues disponibles
A001111-Nutribaby-Notice_Mise en page 1 31/07/15 10:30 Page17
Follow steps 1 to 5 of the baby bottle heating function.
B6. Place the baby food jar to be heated on the insulating grill.
B7. Place the lid on the cooker.
B8. Turn on using the On (I) / Off (O) switch on the back of the blender. The LCD screen on the front of the Nutribaby lights up.
B9. Press the "Mode" button one or more times to choose the desired function.
- If cold baby food is to be heated, select the baby food jar + refrigerator icon
- If lukewarm baby food is to be heated, select the baby food jar + house icon
B10. Press OK to start.
CAUTION: To prevent the risk of burns, always check the temperature of the food before feeding your baby. Let the
bottle sit for 15 or 30 seconds before removing and be extremely careful removing the bottle from the unit. Shake
baby bottles well to mix, then pour a drop of milk on the inside of your wrist to check the temperature.
CAUTION: The pre-programmed cycles are based on the average heating time of a baby bottle or baby food jar. The
material and thickness of the baby bottle, a removable bottom and the size of the baby food jar may affect the
temperature of the food. Heating more than one bottle at once may also affect heating times. If the food is too hot or
too cold, reduce or increase the heating time, using the "steam cooking" function.
These instructions are to be used as a guide only.
Pre-programmed times for baby bottles
Quantity of water/milk
in the baby bottle
Time for a baby bottle
prepared with
lukewarm water
Time for a baby bottle
prepared with
cold water
C1. Connect the cooker to the blender.
C2. Remove the cooking juices receptacle.
C3. Pour 5 fl oz. (150 ml) of water into the tank using the marks on the mixing bowl (level B).
C4. Remove the trays from each steam basket.
C5.Stack the trays, and place them on the base of the Nutribaby.
C6. Place the baby bottles upside down on the tray above the water tank. Add any accessories you also wish to sterilise.
C7. Place the lid on the cooker.
C8. Turn on using the On (I) / Off (O) switch on the back of the blender. The LCD screen on the front of the Nutribaby lights up.
C9. Press the "Mode" button one or more times to choose the desired function. Select the "sterilisation" icon
C10. Press OK to start.
C11. At the end of the cycle, an alarm will sound to inform you that the baby bottles are ready. Press OK to turn off
the alarm.
D1. Connect the cooker to the blender.
D2. Remove the cooking juices receptacle.
D3. Pour 11.7 fl oz. (350 ml) of water into the tank using the marks on the mixing bowl (level A).
D4. Replace the cooking juices receptacle: it will collect the juices from the food, allowing you to preserve nutritional value.
D5. Place the trays in the basket as desired.
B. HEATING A BABY FOOD JAR
3 fl oz.
4 fl oz.
5 fl oz.
(90 ml)
(120 ml)
(150 ml)
2 min 35 2 min 45
3 min
3 min 40 3 min 50 4 min 30 4 min 40
C. STERILIZING
D. STEAM COOKING
NUTRIBABY • Instruction manual
6 fl oz.
7 fl oz.
8 fl oz.
(180 ml)
(210 ml)
(240 ml)
3 min
3 min 10 3 min 10 3 min 10 3 min 15 3 min 25
5 min
5 min 05 5 min 10 5 min 15 5 min 30
.
.
9 fl oz.
10 fl oz.
11 fl oz.
(270 ml)
(300 ml)
(330 ml)
.
17
Publicité
