Livington PRIME Mode D'emploi page 18

to make sure that the surface will not be damaged by its use.
TIP:
• Sweep the floor or use a vacuum cleaner before using the Livington Prime Steam Mop.
• To avoid puddle formation, the microfibre cloth should always be clean and dry. In addition, wring out the microfibre cloth as required.
• To clean an area of your floor hygienically, leave it to work for approximately 10 seconds (but no longer than 15 seconds) on one spot.
Assembling of the hand-held cleaner
1. The hand-held steam cleaner is the ideal portable cleaner for shelves, worktops, wash hand basins, windows, mirrors and tiles.
It can also be used for the selective cleaning of floors, carpets and rugs. Use it with the jet nozzle, the brass brush, the window
cleaner, the scraper edge or the nylon brush to spray dirt, grease, mould and more away.
WARNING: Always remove the mains plug from the socket, before removing the hand-held steam cleaner.
2. Place the steam mop in front of you the floor. Activate the release pedal and pull out the hand steamer from the mop head. Then
press on the release button and slacken the steel tube (Illustration 8).
3. Either add the required attachment or use the appliance with the pre-installed pointed nozzle.
FITTING THE PLUG-IN:
1. Insert anti-clockwise into the plug-in track with gentle pressure. To remove, unscrew clockwise and pull it off (Illustration 9).
WARNING: Never use the circular metal brush on scratch-sensitive surfaces. To remove the brush, turn it clockwise and pull it from
the thread of the jet nozzle.
TIP:
• The circular brush attachment is ideal for stains that are extremely difficult to remove (for example, paint marks on the floor) and
especially suitable for the cleaning of smooth, hard surfaces, such as toilets, wash hand basins, kitchen worktops, wheel rims and
stubborn stains of any kind.
• The circular metal brush is, in turn, especially effective in the cleaning of metallic surfaces, such as brick floors, grillage, metal
doors, metal frames and such like.
• Both brushes can also be used very well for the clearance of grease from pans, cooking hobs and ovens. You can also use them
on dirty spots together with soap or cleaning detergents.
ASSEMBLING OF ADDITIONAL ACCESSORIES
FABRIC CLEANER ATTACHMENT (16)
To use the window cleaner attachment for the cleaning of fabrics, secure the fabric steaming towel to the window cleaner attachment.
USING THE HAND STEAM CLEANER
WARNING: Make sure that the appliance is unplugged.
1. Fill the water container with water (see section: Using the Livington Prime Steam Mop).
2. Fit the required attachments (see section: Fitting of attachments) or use the pre-installed jet nozzle.
3. As soon as the appliance is fully assembled and filled with water, insert the mains plug into an earthed socket. Then activate the
ON/OFF switch (6).
4. The mop will bgein to emit stream after approximately 10 seconds. To stop the steam emission, switch the appliance off with the
aid of the ON/OFF switch.
5. Move the appliance slowly over the surface to be cleaned.
6. If the hand appliance stops emitting steam, fill up the water container, if necessary, and proceed with the cleaning.
7. Make sure the appliance is SWITCHED OFF and the mains plug has been removed from the socket, after each time of use, so that
it is completely SWITCHED OFF before the next time of use.
TIP: To clean worktops, kitchen counters, wash hand basins, bathrooms etc hygienically, leave the steam cleaner to work on one spot
for approximately 15 seconds.
Please Note:
• Do not use the hand steamer on heat and damp-sensitive materials. The power and temperature of the steam may impair some
materials negatively. Therefore, always test first on a non visible spot, to ensure that the surface will not be damaged by its use.
• Do not use the hand steam cleaner for the cleaning of leather, wax treated furniture, waxed floors, synthetic materials, velvet or
other steam-sensitive materials
WINDOW CLEANER ATTACHMENT
WARNING: Make sure that the appliance is unplugged.
1. Fill the water container with water (see section: Using the Livington Prime Steam Mop). Mount the window cleaner attachment
and attach it to the mop (see section: Assembling additional accessories). Switch the appliance on.
2. Guide the cleaner slowly over the glass to be cleaned (or similar surfaces). In doing so, use abundant steam. Keep a hand towel
ready to wipe away any excess water that may have accumulated.
WARNING: RISK OF SCALDING Never touch the window cleaner attachment during application. The corresponding parts can get
18
M16625_M17378_Livington PrimeSteamMop_Manual_A5_20181023_BA.indd 18 23.10.18 12:18