Publicité
Liens rapides
AKiTiO Thunder2 Duo Pro
EN
DE
ES
Setup guide - Setup-Anleitung - Guía de con guración - Guide d'installation
安裝手冊 - 安装手册 - 설치 안내서 - セットアップガイド
For more information and to download the latest
version of this document, please visit our website at
http://www.akitio.com/support/user-manuals
Thunderbolt™ driver for Microsoft Windows
http://www.akitio.com/support/software/
thunderbolt-driver-windows
E15-573T1AA002
© 2015 by AKiTiO - All Rights Reserved
AKiTiO assumes no responsibility for any errors or di erences between the product you
may have and the one mentioned in this document and reserves the right to make
changes in the speci cations and/or design of this product without prior notice. The
diagrams contained in this document are for reference and may not fully represent the
real product. AKiTiO assumes no responsibility for any loss of data or les.
www.akitio.com
FR
CH
KO
PN: E15-573T1AA002
August 20, 2015 - v1.1
[ ] RAID 0
Disk striping for optimal performance.
[ ] RAID 1
Disk mirroring for redundancy and backup.
[ ] SPAN
Disk spanning for large storage.
JP
[ ] Non-RAID
Non-RAID (JBOD) for independent volumes.
Max 3840 x 2160 at 30 Hz
Max 4096 x 2160 at 24 Hz
A Thunderbolt connection is required to use the HDMI port. When
connecting a display via HDMI, you cannot connect a second display
via Mini DisplayPort unless the second one is a Thunderbolt display.
RAID Settings
/
Make sure to backup all existing data rst!
The drives must be formatted after changing the RAID mode.
HDMI Display
Publicité
Manuels Connexes pour Akitio Thunder2 Duo Pro
Sommaire des Matières pour Akitio Thunder2 Duo Pro
- Page 1 © 2015 by AKiTiO - All Rights Reserved Max 4096 x 2160 at 24 Hz AKiTiO assumes no responsibility for any errors or di erences between the product you A Thunderbolt connection is required to use the HDMI port. When...
- Page 2 Front View - Frontansicht - Vista frontal - Vue de face Rear View - Rückansicht - Vista posterior - Vue arrière 正面 - 正面 - 정면도 - フロントビュー 背面 - 背面 - 배면도 - リアビュー (20 Gbps) Fan (ON/OFF) Green = Power ON Blue = Power ON / Link established Thunderbolt port...
- Page 4 3.5” Drives 2.5” Drives...
- Page 5 The new RAID mode can be con rmed either by pressing 15 = RAID 0 30 = SPAN the [Set RAID] button while the device is turned on or by power cycling it. The best way is to set the RAID mode, 75 = RAID 1 assemble the device and then turn it on.
- Page 6 Initial Setup Thunderbolt 2 & USB 3.0 Dual Interfaces Select the RAID mode and assemble the device. Turn on your computer, Always connect the interface cable and turn on your computer rst, connect the interface cable and then plug in the power adapter to turn before turning on the power.
- Page 7 Replacing a faulty drive Reemplazar una unidad defectuosa When a drive fails, the corresponding LED (A/B) lights up red. If only Cuando una unidad falla, el LED correspondiente (A/B) se ilumina en one drive is defective and the RAID mode is set to RAID 1, the data can rojo.
- Page 8 更換故障的磁碟 고장난 드라이브 교체하기 HDD Error時相對應的LED會亮紅燈。如果只有一個磁碟發生故障， 드라이브가 제대로 인식되지 않았을 때 LED(A/B) 등 빨간 불이 磁碟陣列模式設定為RAID 1的，該資料仍然可以讀寫，但建議請立 들어옵니다. RAID 1 모드일 때 , 하나의 드라이브에서만 문제가 발생 即更換有故障的磁碟。如果有多個磁碟同時出現故障或者磁碟陣列 하였다고 해도 사용가능 하지만, 문제의 드라이브를 빨리 模式設定為RAID 0或SPAN者，所有資料都將遺失。對於Non-RAID 교체하시길 권장합니다. 동시에 하나이상의 드라이브가 고장나거나 ，只有發生錯誤磁碟上的資料會遺失。...