Operation; Replacing The Power Cable - EINHELL RT-MG 200 E Instructions D'origine

be placed against the plug-in tool.
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the va-
cuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
5.3 Fitting the dust extraction device
(Fig. 4/5)
The dust extraction system prevents the accumu-
lation of dirt and high dust loads in the air, and it
makes it easier to dispose of the dust.
•
Place the equipment in a stable position as
shown in 5.1.
•
Fit the dust extraction device (6) with the tool
mounting (2) positioned as shown in Figure 4.
•
Fasten the dust extraction device (6) by lat-
ching it in the air vents.
•
Connect the extractor adapter (3) to the dust
extraction device (6). Make sure that the ar-
row (a) on the extractor device coincides with
the recess (b) on the dust extraction device
(6) (see Fig. 5). Turn the extractor adapter (3)
anti-clockwise until it engages..
•
Connect your tool to an extraction unit or va-
cuum cleaner. This will provide excellent ext-
raction of chips and dust from the workpiece.
The benefi ts are that you will protect both the
equipment and your own health. Your work area
will also be clean and safe.

6. Operation

6.1 Switching on/off
Slide the switch (1) forwards to switch on the
equipment.
6.2 Practical tips
•
Switch on the equipment.
•
Work away from the body.
•
Never move your hands into the direct vicinity
of the work area.
•
Use only plug-in tools which are in good wor-
king order and undamaged.
Anl_RT_MG_200_E_SPK1.indb 19 Anl_RT_MG_200_E_SPK1.indb 19
GB
Plug-in tools
Sawing: Sawing wood and plastic.
Notes on working practice: When sawing, watch
out for foreign bodies in the workpiece and remo-
ve these if necessary. Plunge cutting is allowed
only in soft materials such as wood or plaster-
board.
Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depen-
ding on choice of sanding/grinding paper for the
sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice: This equipment off ers
particularly high performance for the sanding/
grinding of hard-to-reach corners and edges. To
sand/grind profi les and channels you can also
work with just the tip or the edge of the sanding/
grinding disk. Various sanding/grinding papers
are available, specially designed for the diff erent
types of material you may be working on and the
amount you wish to remove from the surface.
The amount removed will depend largely on the
choice of sanding/grinding paper and pressure
applied to the sanding/grinding disk.
Scraping: Scraping off old paint or adhesives.
Notes on working practice: Move the plug-in tool
against the area you want to remove. Begin with
a fl at angle of incidence and little pressure. The
surface (e.g. wood, plaster) may be damaged if
too much pressure is used.
6.3 Speed control (Fig. 6)
You can select the speed by turning the speed
controller (4).
Plus direction: Higher speed
Minus direction: Lower speed

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 19 -
30.03.15 16:21 30.03.15 16:21