EINHELL OPAL Instructions De Montage page 5

Important note: The outside of the plastic web
panels (with UV coating) is marked „Außenseite /
Outside" at the edge, and it is also the side onto
which the protective film has been stuck. Only
remove the protective film from the plastic web panel
you are currently installing.
Page 19
Top illustration: Assembly preview / reference
diagram (side) (illustration shows a 5-panel
greenhouse)
Page 20
Figure 26/d: Profile diagram (double clip / side strut)
Tip: Use a solid object (e.g. the handle of a
screwdriver) to lightly tap several times on the clips
and knock them from the top down into position.
Page 21
Figure 26/e: Profile diagram (single clip / corner
profile)
Important note: Make sure that the narrow side of
the spacers is attached to the floor profile. The wider
side is used to fix the plastic web panel.
Page 22
27
Assembly of the plastic web panels on the
window rabbet profile
Important note: The outside of the plastic web
panels (with UV coating) is marked „Außenseite /
Outside" at the edge, and it is also the side onto
which the protective film has been stuck. Only
remove the protective film from the plastic web panel
you are currently installing.
Page 23
27/d: Loosen the bolts on the window rabbet profile
and slide the window rabbet profile far enough down
until the plastic web panel is fully enclosed (refer to
the profile diagram 27/d). Then retighten the nuts.
Page 24
28
Assembly of the plastic web panels
on the roof
Important note: The outside of the plastic web
panels (with UV coating) is marked „Außenseite /
Outside" at the edge, and it is also the side onto
which the protective film has been stuck. Only
remove the protective film from the plastic web panel
you are currently installing.
ABA_OPAL_Teil2_Titel+GB.pmd 5
Page 25
Top illustration: Assembly preview / reference
diagram (roof) (illustration shows a 5-panel
greenhouse)
Page 26
Please note (Figure 28/c): Always use a safety
stepladder when installing the clips on the roof, and
also take great care to ensure that the stepladder has
a secure footing.
Tip: Use a solid object (e.g. the handle of a
screwdriver) to lightly tap several times on the clips
and knock them from the top down into position.
Figure 28/d: Profile diagram (double clip / side strut)
Figure 28/e: Profile diagram (single clip / corner
profile)
Page 27
29
Assembly of the rubber profile on the
window rabbet profile
29/a + 29/b: Cut a length of approximately 73 cm of
window sealing profile and pull it into the guide rail of
the window rabbet profile (refer to the profile dia-
gram). Make sure that the rubber protrudes slightly
above the two clips on the roof struts.
Page 28
30
Pre-assembly of the single door
Important note: The outside of the plastic web
panels (with UV coating) is marked „Außenseite /
Outside" at the edge, and it is also the side onto
which the protective film has been stuck. Only
remove the protective film from the plastic web panel
you are currently installing.
Important note – take care not to mix up the
components: There is only a minimal difference in
terms of size between the washers 52.036.10 and
52.046.10. Please make sure that you use the
smaller washer 52.036.10 to assemble the door
handle in this step.
Page 29
30/a: Slide the DT latch (Pos. 3) into the guide rail of
the door closing profile with the hole (item 11). In
addition, attach a hexagonal bolt approximately 5 cm
from the edge at both ends of this guide rail (refer to
the profile diagram).
30/b: One bolt needs to be pre-assembled at each
end of two door closing profiles (approx. 5 cm from
the edge) (item 9).
30/c: On the third door closing profile (item 9), two
bolts need to be pre-assembled in the middle and two
bolts at each end, approximately 5 cm from the edge.
05.04.2006, 22:37
5