Cleaning And Maintenance - Asist AE2S03DN-50 Mode D'emploi

Charge the battery only in dry areas.
There is a risk of injury from electric shock.
• The device may only be powered with SELV (Safety
Extra Low Voltage) as marked on the device.
• Before initial use, charge the battery installed in the
equipment. Do not charge the battery for several short
periods in succession.
• To charge the integrated Li-ion battery of the device,
preferably use the battery charger supplied.
• In all cases, observe the applicable safety
information as well as the regulationsand directions for
environmental protection.
• Defects resulting from improper handling are not
subject to the guarantee.
Charging the battery
1. Connect the charging cable connector (12) with the
charging socket (7) of the device.
2. Plug the charger ( 13) into an electrical outlet.
3. The battery indicator (3) lights up:
red => Start of charging
red and yellow => Battery appr. half charged
red-yellow-green =>
Battery fully charged.
4. After the charging process, disconnect the charger (
13) from the mains supply.
Initial Operation
Wearing hearing protection reduces the risk of hearing
damage.
Switching ON and OFF
1. Press the on/off switch (8) to start the device. The
LED work light (10) lights up during operation.
2. To turn it off, release the on/off switch (8).
Overload protection: The safety cut-off of the device
switches off in case of overload.
Release the On/Off switch, the device can be switched
on again after a few seconds.
Checking the charge status of the rechargeable battery
The battery indicator ( 3) signalises the state of charge
of the battery.
• Press the On/Off switch, the state of charge of the
battery is displayed by turning on the 3 coloured LED
lights:
red-yellow-green => Battery fully charged
red and yellow =>
Battery appr. half charged
red => Battery is empty, please charge.
Set the direction of rotation
You can select the direction of rotation with the direction
switch (clockwise and anticlockwise direction) and
secure the device against accidental start up.
1. Wait for the device to shutdown.
2. Clockwise direction:
Press direction switch (9) to the right.
3. Anticlockwise direction:
Press direction switch (9) to the left.
4. Switch lock: Bring direction switch to neutral
position.
Direction switch may only be activated at a standstill to
prevent damage to the transmission.
Inserting/replacing bits
Prior to commencing any work on the device, bring the
direction switch ( 9) to the neutral position
in order to prevent an accidental start up.
1. Insert the desired bit (14) or bit holder (15) into the
bit adapter (11). It locks into place audibly.
2. To remove the bit or bit holder pull the spring sleeve
(1) back.
3. With the spring sleeve (1) pulled back remove the bit
or bit holder from the bit adapter (11). Release
the spring sleeve.
Torque setting
Always turn off the device, before setting the torque.
1. Turn the adjusting ring (2) to select the desired
torque:
Step 1 --> lowest torque,
Step MAX --> highest torque (5 Nm).
2. Start with a lower torque step and increase
according to requirement.
The necessary torque is dependent on:
- the type and hardness of the material to be treated;
- the type and length of the screws used.
Handle setting
Prior to commencing any work on the device, bring the
direction switch ( 9) to the neutral position in
order to prevent an accidental start up.
The device can be locked in two hand settings:
- Pistol grip position
- Rod position
Press the release key PRESS (4) and turn the handle
(6) of the device by 180°. It locks into place audibly.
Use as a torch
1. Press the torch lens (5) on the underside of the
handle (6). The torch LEDs light up.
2. To switch off the LEDs press the torch lens (5) again.

CLEANINg AND MAINTENANCE

Clean and service the device regularly as follows.
This guarantees a long life for your unit: Do not jet
water onto the appliance and do not clean it under
flowing water. This would result in the danger of an
electric shock and the appliance could be damaged.
• Keep the ventilation slits, motor housing and handles
on the equipment clean. To do this, use a damp cloth
or brush.
Never use cleaning agents or solvents, which can
cause irreparable damage to the unit.
Maintenance
The device is maintenance free. Storage
• Keep the device in the blade guard supplied, dry and
out of reach of children.
• Store the battery only in a partially charged state. The
state of charge should be 40 – 60 % over a longer
storage period.
• Store the device between 10° C and 25° C. During
storage, avoid extreme cold or heat so the battery
does not lose power.
• During a longer storage period, check the state
of charge of the battery and recharge if necessary
roughly every 3 months.
46