General Inspection - PRO-PULSE 10CSMS Guide De L'utilisateur

OPERATING INSTRUCTIONS
11) Hold the operating handle (3) firmly and
squeeze the switch trigger (19). Allow
the blade to reach maximum speed and
slowly lower the blade into and through
the workpiece.
12) Release the switch trigger (19) and allow
the saw blade to stop rotating before
raising the blade out of the workpiece.
Wait until the blade stops before removing
the workpiece.
Compound mitre cut
A compound mitre
cut involves using a
mitre angle and a bevel
angle at the same time.
It is used in making
picture frames, to cut
mouldings, making
boxes with sloping
sides and for roof
framing. Always make a test cut on a piece
of scrap wood before cutting into the good
material.
Use the slide action when cutting wide
workpieces.
1) Pull on the release knob (2) and lift the saw
arm to its full height.
2) Loosen the mitre lock (20).
3) Rotate the mitre table (16) until the pointer
aligns with the desired angle on the mitre
scale (17).
4) Retighten the mitre lock (20).
WARNING. Be sure to tighten the mitre lock
before making a cut. Failure to do so could
result in the table moving during the cut,
causing serious personal injury.
5) Loosen the bevel lock (12) and pull out the
0º bevel adjuster and move the saw arm (1)
to the left or right to the desired bevel angle
(between 0º and 45º). Tighten the bevel lock
E
(12).
6) Place the workpiece flat on the table with
one edge securely against the fence (14).
If the board is warped, place the convex
side against the fence. If the concave side
is placed against the fence, the board could
break and jam the blade.
30
7) When cutting long pieces of timber, support
the opposite end of the timber with the side
bars (29), a roller stand or a work surface
that is level with the saw table.
8) Use the clamp assembly (6) to secure the
workpiece wherever possible.
9) It is possible to remove the clamp assembly
(6) by loosening the clamp assembly lock (7)
and moving it to the other side of the table.
Make sure the clamp assembly lock is tight
before using the clamp.
10) Before turning on the saw, perform a dry
run of the cutting operation to check that
there are no problems.
11) Hold the operating handle (3) firmly and
squeeze the switch trigger (19). Allow
the blade to reach maximum speed and
slowly lower the blade into and through the
workpiece.
12) Release the switch trigger (19) and allow
the saw blade to stop rotating before
raising the blade out of the workpiece.
Wait until the blade stops before removing
the workpiece.
Maintenance
1) Store the tool, instruction manual and
accessories in a secure place. In this way
you will always have all the information and
parts on hand.
2) Keep the tool's air vents unclogged and
clean at all times.
3) Remove dust and dirt regularly. Cleaning
is best done with compressed air or a rag.
4) Never use caustic agents to clean
plastic parts.
5) Lubricate the guide roller from time to time
with a drop of oil. It will extend the life of
the roller.
CAUTION. Do not use cleaning agents to
clean the plastic parts of the tool. A mild
detergent on a damp cloth is recommended.
Water must never come into contact with
the tool.

General inspection

Regularly check that all the fixing screws are
tight. They may vibrate loose over time.
WARRANTY
Warranty
Thank you for investing in a PRO-PULSE
power tool. These products have been made
to demanding, high-quality standards and
are guaranteed for domestic use against
manufacturing faults for a period of 12 months
from the date of purchase. This guarantee
does not affect your statutory rights. In case
of any malfunction of your tool (failure, missing
part, etc.), please contact one of our service
technicians
at our toll free service line at 1 866-206-0888
from 8 AM to 8 PM, Monday to Friday, Eastern
time. RONA reserves the right to repair or
replace the defective tool, at its discretion.
Normal wear and tear, including accessory
wear, is not covered under guarantee. The
product is guaranteed for 12 months if used
for normal trade purposes. Any guarantee is
invalid if the product has been overloaded
or subject to neglect, improper use or an
attempted repair other than by an authorized
agent. Heavyduty, daily professional or hire
usage are not guaranteed. Due to continuous
product improvement, we reserve the right to
change the product specification without prior
notice.
E
31