Publicité
Les langues disponibles
Les langues disponibles
FCC compliance information statement
Product Name: Gigabit Desktop Switch
Model Number: TL-SG1005LP/TL-SG1005P
Component Name
Model
I.T.E. POWER SUPPLY T535081-2-DT (For TL-SG1005LP)
T535131-2-DT (For TL-SG1005P)
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.• Reorient or relocate the receiving antenna.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been
shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized
change is made in the equipment and the equipment is properly maintained and operated.
Avertissement de marque CE
Il s'agit d'un produit de classe A. Dans un environnement domestique, ce produit peut
provoquer des interférences radio, auquel cas l'utilisateur peut être tenu de prendre des
mesures adéquates.
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。
限用物質含有情況標示聲明書
限用物質及其化學符號
產品元件名稱
鉛
鎘
汞
Pb
Cd
Hg
PCB
外殼
電源供應器
備考 1". "系指該項限用物質之百分比含量未超出百分比含量基準值。
備考 2". "系指該項限用物質為排除項目。
Issue Date: 2020.2.24
六價鉻 多溴聯苯 多溴二苯醚
Cr
PBB
PBDE
+6
FCC compliance information statement
Product Name: I.T.E. POWER SUPPLY
Model Number: T535081-2-DT/T535131-2-DT
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been
shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized
change is made in the equipment and the equipment is properly maintained and operated.
Exigences de montage
Pour monter l'appareil sur un mur, utiliser 2 vis conformes à ANSI B1.1 4#, (5#), 6#, 8# standard
et mesurent plus de 8,5 mm de longueur. Lorsque les vis sont fixées sur le mur, la distance entre
la tête de vis et le mur doit être supérieure à 1,5 mm.
Diameter
Standard
ANSI B1.1 #4
2.845 mm
ANSI B1.1 #5
3.175 mm
ANSI B1.1 #6
3.505 mm
ANSI B1.1 #8
4.166 mm
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
Explication des symboles sur l'étiquette du produit
Tension DE COURANT
Utilisation à l'intérieur seulement
Recyclage
Ce produit porte le symbole de tri sélectif pour les déchets d'équipement
électrique et électronique (DEEE). Cela signifie que ce produit doit être
manipulé conformément à la directive européenne 2012/19/UE afin d'être
recyclé ou démantelé afin de minimiser son impact sur l'environnement.
L'utilisateur a le choix de donner son produit à une organisation de recyclage
compétente ou au détaillant lorsqu'il achète un nouvel équipement électrique
ou électronique.
Polarité des terminaux de sortie
Marquage de l'efficacité énergétique (niveau VI)
Issue Date: 2020.2.24
Publicité
