Technical Data - Prowork PEH 2135 Mode D'emploi

Anleitung PEH 2135 SPK 1
contacts and the coupling must be rain-water-
protected.
Use only original replacement parts for repair and
maintenance purposes.
Have repairs carried out only by a qualified
electrician.
Examine the grass trimmer for signs of wear or
damage each time before you use it and after any
collisions. Have essential repairs carried out
without delay.
Never use replacement parts or accessories which
are not foreseen or recommended by the
manufacturer.
Pull out the power plug before carrying out any
inspection, cleaning or other work on the trimmer
and whenever it is not being used.
Before you begin your work, examine the material
you want to shred. Remove any foreign bodies.
Continue to watch out for foreign bodies while you
are working. If you come across any foreign
bodies while shredding, shut down the machine
and remove the items in question.
Keep the machine away from other persons,
particularly children and pets.
Use the machine only in the way described in
these operating instructions.
The electric circuit must be protected at least by a
10A fuse.
The efficiency of the machine will be greatly
reduced if a connecting cable with too small a
cross section is used. A conductor cross section of
at least 3x1.5 mm2 is required for cables up to 25
m long, and one of at least 3x2.5 mm2 for cables
longer than 25 m.
If the machine has to be lifted for transporting, be
sure to switch off the motor first and wait for the
cutter to come to a standstill. Each time before you
leave the machine, switch off the motor and pull
out the power plug. Before you connect the
machine to the power supply, make sure that the
loading funnel is properly connected to the motor
housing and the release screw tightened.
If the garden refuse shredder vibrates excessively,
turn off the motor, pull out the power plug, and find
out immediately what is causing the vibrations.
Intensive vibration is usually a sign that something
is wrong.
Caution! The cutters continue to run for a few
seconds after the motor is switched off.
11.05.2005 7:52 Uhr Seite 9
2. Description of the warning sign (see
Fig. 1) on the machine
1. Important! Read the operating instructions
and follow the warnings and safety instructi-
ons
2. Important! Always wear safety goggles, ear
protection, protective gloves and heavy-duty
work clothes. We recommend that you wear a
helmet with a face guard.
3. Important! Protect the machine from the
damp and never expose it to rain.
4. Always set the ON/OFF switch to OFF and
pull the power plug out of the socket-outlet
before doing any work on the shredder, e.g.
cleaning the shredder and making adjust-
ments, or if the power cable becomes dama-
ged.
5. Important! If the mains lead is damaged or
cut, pull out the power plug immediately.
6. Caution! Pieces of shredded material may be
catapulted out of the shredder during operati-
on. Keep a safe distance between yourself
and the machine.
7. Caution! Rotating cutters. The cutters conti-
nue to run after the motor is switched off.
Wait for the cutters to come to a standstill.
Risk of injury!

3. Technical data

Voltage:
Power rating:
Idle speed n0
Branch diameter:
LPA sound pressure level:
LWA sound power level:
Weight:
S6 (40%) stands for a duty cycle based on 4 minutes
on-load and 6 minutes off-load operation. Maximum
power consumption depends on the consistency of
the material being shredded.
4. Layout of the (Figure 2/3)
1 Loading funnel inlet
2 Loading funnel
3 Motor housing with cutter plate
4 Transportation handle
GB
230 V ~ 50 Hz
2100 W (S6-40%)
1700 W (S1)
2900 min -1
max. 35 mm
84 dB (A)
104 dB (A)
17,3 kg
9