Muse M-58 BT Manuel De L'utilisateur page 6

SETTING THE TIME
1. In standby mode, press and hold CLOCK button on remote control until the clock hour flashes on display.
2. Press / to set the hour and then press CLOCK to confirm, the minute digits blink.
3. Press / to set the minute. Press CLOCK again to save setting.
4. To check the clock time at any time, press CLOCK once.
Clock Synchronization
In the standby mode, press and hold the / MENU button on the remote control for few seconds, then the unit will enter the CLOCK
SYNC mode.
Note: This feature is not available if no RDS station can be received.
SLEEP FUNCTION
In sleep mode, the unit will turn off automatically after a specified time. You can select duration in minutes before the unit turns off
automatically.
1. When the unit ON, Press SLEEP / TIMER button on remote control repeatedly to select 90-60-30-15-00.
Notes:
- Sleep time can only be set when the unit is turned ON.
- The sleep function is cancelled when "00" is selected.
2. Press SLEEP / TIMER button to check the remaining sleep time.
3. If you want to switch off the unit before sleep time ends, press
ALARM TIMER SETTING
1. In standby mode, press and hold the SLEEP / TIMER button on remote control, the hour digits will blink.
2. Press or button on remote control to set the hour. Press SLEEP / TIMER button to confirm the hour, the minute digits will
blink.
3. Press or button on remote control to set the minute. Press SLEEP / TIMER button to confirm the minutes.
4. Press or to select the source of wake up: BUZZER / FM / USB / DISC.
5. Press SLEEP / TIMER button to confirm. Alarm volume level digits will show on the display, press
level.
6. Press SLEEP / TIMER button again to confirm alarm volume level setting and complete the whole alarm setting process, "
will show on the display.
Activate and Deactivate the Alarm Timer
- In standby mode, Press SLEEP / TIMER button on remote control to review the alarm settings.
- To activate the alarm, Press SLEEP / TIMER button twice on remote control, "
- To deactivate the alarms, press the SLEEP / TIMER button twice on remote control, "
DISPLAY DIMMER
Press the DIMMER button on the remote control repeatedly to change the backlight brightness of the display.
LISTENING TO THE RADIO
MANUAL SEARCH
1. When the unit is on, press on unit or press FM on remote control to select FM RADIO function.
2. Press repeatedly or to find your station.
3. Adjust the sound level by pressing – or + on unit or VOL- or VOL+ on remote control.
AUTOMATIC SEARCH
1. When the unit is on, press on unit or press FM on remote control to select FM RADIO function.
2. Press and Hold on or for about 2 seconds to start the search. The automatic search function locates station whose signal
is strong.
For optimal radio reception:
FM: Extend and position the antenna wire.
Note:
Stations with weak signals can be searched manually.
The sound is automatically muted during search.
RADIO PRESET STATIONS
You can preset up to 20 FM stations.
Manual storage:
1. In FM mode, Select a station manually or automatically with
2. Press PROG, "XX" blinks on the display for a few seconds.
3. Press or to select a preset number.
4. Press PROG again to store the radio station on the selected memory number.
5. Repeat steps 1-4 to store other stations.
HX-3621 IB MUSE 001 REV0.indd 6
button.
or to adjust the sound
" appears from display.
" disappears from display.
or .
EN - 3
Automatic storage:
In FM mode, Press and hold PROG, "AUTO" indicator appear on display, unit will automatically search and save the available 20
FM stations.
Note:
When you store on a channel already been preset, the previous station will automatically be cleared and replaced by the new station.
Listen to station presets
1. Press to select the previous preset station or press
2. Adjust the sound level by pressing – or + on unit or VOL- or VOL+ on remote control.
Show RDS information
RDS (Radio Data System) is a service that allows FM stations to show additional information. If you tune to a RDS station, the station
name are displayed. When automatic programming is used, RDS stations are programmed first.
1. Tune to a RDS station.
2. Press the INFO button repeatedly to scroll through the following information (if available): Station name, PTY, CLOCK INFO,
Frequency, RADIO TEXT.
CD OPERATION
1. Press to turn on the unit.
2. Open the CD door by pushing .
3. Place the CD with label side facing outward to the CD compartment and press
close the CD door.
IMPORTANT: The CD Door is Motorized Door. Do not push with hand or use any other
means to open or close it. This could damage the door mechanism.
4. Press on unit or press CD on remote control to select DISC function.
on the display.
5. After a few seconds, playback starts automatically.
"
Permanently stop playback: Press
Pause playback: Press
Resume playback: Press
- Search forward or backward: Press and hold
- To skip to the next or previous track: Press
Repeat current track displayed.
Repeat folder flashing
Repeat all tracks displayed.
DISC ERROR
Note: If the disc is dirty, damaged or unreadable, or if the disc is placed upside down, "NO DISC" will appear on the display. If this
occurs, clean the disc, insert the disc correctly or try another disc.
PROGRAM
1. Place the CD with label side facing outward to the CD compartment and press to close the CD door.
2. Press / MENU on remote control
3. Press PROG on remote control. "P0X" light up and "T0X" blinking.
4. Select the desired track with / then press PROG to save the program in memory.
5. Repeat step 4 until the end of your programming.
6. Press to start playback.
7. To cancel current program, press / MENU button twice on remote control.
CD/Mp3 up to 20 programs.
LISTENING TO DEVICE USB
1. Press to turn the unit on.
2. Connect a USB device containing MP3 files to the USB port.
3. Press button on unit or press USB button on remote control to select the USB function.
"USB" and " " appears on the display.
4. After a few seconds, playback starts automatically.
5. Adjust the sound level by pressing – or + on unit or VOL- or VOL+ on remote control.
repeatedly to select the next preset station.
to
appears
/ MENU
/ PAIR
/ PAIR again
or
or
EN - 4
2014/7/31 15:39:06