To tune frequency automatically:
1. Press and hold or to tune frequency automatically.
2. Press or to stop scanning and select a frequency.
To decrease interference or electrical noise, adjust the
position of the antenna or move the product to a higher
elevation.
STORING A PRESET IN MEMORY
See page 10.
The memory feature saves up to 20 frequencies as presets
in the product's memory. You can save up to 10 frequencies
each for FM and AM modes.
Tune to the desired FM or AM frequency.
1. Press and hold
until "MEMORY" and the preset
position number flash on the screen.
2. Press and to choose a preset position number.
NOTE: There are 10 preset positions for FM and 10
for AM. Only one station can be saved in each preset
position.
3. Press
again to store the frequency.
To tune to presets (fm or am mode):
■
Press and release
position number and its associated frequency.
EQUALIZER FUNCTION
To adjust the bass and/or treble settings:
1. Press and hold
until "b" (BASS) is displayed.
Press again and "t" (TREBLE) is displayed.
2. Press
or
until the desired bass or treble level (–5
to 5) is achieved . Press
SETTING THE CLOCK
See page 11.
1. Press and hold
until the hour time blinks.
2. Press
or
to select the hour.
NOTE: Time is displayed in 12-hour format only. To
select an hour that is afternoon and before midnight,
cycle the hours until "PM" appears in the display.
3. Press and release
to lock in the hour setting. Minute
time blinks.
4. Press
or
to select the desired minute.
5. Press and release
again to confirm the time.
USING A PHONE/MP3 PLAYER (NOT INCLUDED) WITH
THE PRODUCT
See page 12.
NOTE: The retainer strap may be used to secure the
device into position.
1. Press
until AUX mode is highlighted.
2. Connect auxiliary cable (not included) to the device.
NOTE:
The phone/MP3 player must be on and in play
–
mode for sound to be heard through the speakers.
All phone/MP3 player controls can be used normally
–
4
to cycle through each preset
to store your selection.
while connected to radio.
Volume for any device connected through the
–
auxiliary cable can be adjusted using the volume
control for that device or by using
product.
Turning the product off will not turn the phone/MP3
–
player off.
The auxiliary cable does not provide charging
–
function.
3. For complete operating instructions for the connected
device, always refer to the manual that was included
with your device.
USING A BLUETOOTH
ENABLED DEVICE (NOT IN-
®
CLUDED) WITH THE PRODUCT
See page 13.
1. Press
until the BLUETOOTH
NOTE:
When the product is switched to BLUETOOTH
–
mode, the product will attempt to pair to a
BLUETOOTH
®
enabled device and "bt" will flash in
the LCD display.
The product will automatically attempt to connect
–
to the last device it was paired to. If a connection
cannot
be
established
the product will make itself available to other
BLUETOOTH
®
enabled devices.
BLUETOOTH
enabled devices must be within 30
®
–
ft. of the product and set to search/scan in order to
pair with the product.
2. Select "RYOBI Radio" from your device's list of
available BLUETOOTH
®
and the product. No password or PIN is required for
connection.
NOTE:
When the device has successfully paired with the
–
radio, "bt" will stop flashing.
When a device is paired to the product, information
–
for connecting to the device is saved in the radio's
memory.
3. Press
and
to go to the previous or next track when
streaming audio from a BLUETOOTH
4. Press and release
playing the audio.
NOTE:
These controls may not be supported by the
–
BLUETOOTH
device and application.
®
All BLUETOOTH
enabled device controls can be
®
–
used normally while paired to the product.
Volume for any device paired to the product can be
–
adjusted using the volume control for that device or
by pressing
or
on the product.
5. Press and hold
to disconnect the all BLUETOOTH
enabled device.
NOTE: When the device is disconnected, "bt" will begin
flashing in the LCD display and the product will begin
searching for another device.
English
or
of the
®
mode is highlighted.
within
five
seconds,
signals to pair the device
®
enabled device.
to cycle between pausing and
®
®