Things You Should Know - Aerotec Airliner 5 GO Manuel Utilisateur

GB
Preserve this handbook for future reference
1. PRECAUTIONS
All users must read and fully understand all information
contained in this owner's manual before assembling, operating,
or maintaining this air compressor.
Carefully review the following rules for safe operation and fully
understand all warnings.
An ACOUSTIC PRESSURE value of 4 m. corresponds to the
ACOUSTIC POWER value stated on the yellow label located on
the compressor, minus 20 dB.
THINGS TO DO
● The compressor must be used in a suitable environment (well
ventilated with an ambient temperature of between +5°C and
+40°C) and never in places affected by dust, acids, vapours,
explosive or flammable gases.
● Always maintain a safety distance of at least 4 meters between the
compressor and the work area.
● Any coloring of the belt guards of the compressor during painting
operations indicates that the distance is too short.
● Insert the plug of the electric cable in a socket of suitable shape,
voltage and frequency complying with current regulations.
● Use extension cables with a maximum length of 5 meters and of
suitable cross-section.
● The use of extension cables of different length and also of adapters
and multiple sockets should be avoided.
● Always use the I/O switch to switch off the compressor.
● Always use the handle to move the compressor (fig. 4).
● Always disconnect power cord and air hose from the air compressor
before transporting.
● When operating, the compressor must be placed on a stable,
horizontal surface.
● The compressor must only and exclusively be operated in a
horizontal position (fig. 1), standing on two strips of rubber located
at the opposite side of the control panel.
NOT
THINGS TO DO
● Never direct the jet of air towards persons, animals or your body.
(Always wear safety goggles to protect your eyes against flying
objects that may be lifted by the jet of air).
● Never direct the jet of liquids sprayed by tools connected to the
compressor towards the compressor.
● Never use the appliance with bare feet or wet hands or feet.
● Never pull the power cable to disconnect the plug from the socket
or to move the compressor.
● Never leave the appliance exposed to adverse weather
conditions.
● Never transport the compressor with the receiver under pressure.
● Do not weld or machine the receiver. In the case of faults or rusting,
replace the entire receiver.
● Never allow inexpert persons to use the compressor. Keep children
and animals at a distance from the work area.
● This appliance is not intended for use by persons (including
2. FEATURES (Pics. 1-2-3)
A. I/O Switch: The I/O switch is the activation mechanism that is
used to start and stop the compressor. When the switch is "On",
the motor and pump will compress air until tank pressure reaches
the upper limit of the factory set operating pressure. When
tank pressure falls below the factory set "cut in" pressure, the
compressor will again automatically start to compress air.
B. Tank Pressure Gauge: The tank pressure gauge indicates the air
pressure that is present in the tank in PSI (and BAR).
C. Regulated Pressure Gauge: The regulated pressure gauge
indicates the amount of pressure that is allowed into the discharge
line according to the setting of the regulator.
D. Regulator Knob: The regulator knob is used to adjust the air
pressure that is available at the discharge line. The discharge
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a
person responsible for their safety.
● Children should be supervised to ensure that they do not play with
the appliance.
● Do not position flammable or nylon/fabric objects closed to and/or
on the compressor.
● Never clean the compressor with flammable liquids or solvents.
Check that you have unplugged the compressor and clean with a
damp cloth only.
● The compressor must be used only for air compression. Do not use
the compressor for any other type of gas.
● The compressed air produced by the compressor cannot not be
used for pharmaceutical, food or medical purposes except after
particular treatments and cannot be used to fill the air bottles of
scuba divers.
● To avoid serious burns, never touch the cylinder head parts or
tubing during or immediately after operation.

THINGS YOU SHOULD KNOW

● To avoid overheating of the electric motor, this compressor is
designed for intermittent operation (do not operate on more than
a 15% duty cycle. If this air compressor pumps air more than 15%
of one hour, then the compressor's capability is less than the air
delivery required by the application. Always match the air volume
requirements of the attachment or accessory with the air volume
delivery of the compressor). In the case of overheating, the thermal
cut-out of the motor trips, automatically cutting off the power when
the temperature is too high. The motor restarts automatically when
normal temperature conditions are restored.
● When the compressor is plugged into an electrical source and
the I/O switch is in the "ON" position, this compressor will
cycle automatically.
– Never touch any moving parts.
– Keep all body parts, hair, clothing, and jewelry away from moving
parts.
– Never operate the air compressor without all guards and shrouds
in place.
– Never stand on the compressor.
● The compressor is fitted with a safety valve that is tripped in the case
of malfunctioning of the pressure switch in order to assure machine
safety.
● The red notch on the pressure gauge refers to the maximum
operating pressure of the tank. It does not refer to the adjusted
pressure.
● When fitting a tool, the flow of air in output must be switched off.
● When using compressed air, you must know and comply with
the safety precautions to be adopted for each type of application
(inflation, pneumatic tools, painting, washing with water-based
detergents only, etc.).
● Never exceed the maximum allowable pressure recommended by
the manufacturer of any attachment or accessory you use with this
compressor.
air pressure is increased by turning the knob clockwise and
decreased by turning the knob counter clockwise.
E. Drain Valve: Ball style valve that drains moisture from the tank
when opened.
F. Quick Coupler: The quick coupler is used to connect the airline
to your tool.
G. Safety valve: The safety valve is set to avoid over-pressurization
of the air tanks. This valve is factory pre-set at 10 bar (145 PSI)
and will not function unless tank pressure reaches this pressure.
Do not attempt to adjust or eliminate this safety device.
Any adjustments to this valve could cause serious injury. If
this device requires service or maintenance, see an Authorized
Service Center.
H. Handle for lifting/moving.
11
G
B