Publicité
5' VENT EXHAUST KIT MODEL HEVK-5
INSTALLATION INSTRUCTIONS
Install Only on HEDV
WARNING:
USE ONLY COZY HEATING SYSTEMS, LLC FACTORY SUPPLIED PARTS AND KITS. FAILURE TO DO SO
COULD RESULT IN LOSS OF LIFE, PERSONAL INJURY, PROPERTY DAMAGE OR UNSATISFACTORY
PERFORMANCE. THIS KIT MUST BE INSTALLED BY A QUALIFIED INSTALLER OR SERVICE TECHNICIAN.
C
G
D
E
CONTENTS
OF KIT:
Description
Part No.
A. Steel Coupling (2" x 3")
72532
B. Black Floating Tube (2" x 5')
72575
C. Black Flex Tubing (2" x 6')
72612
D. Support Brackets
41515
E. Center Bracket
41520
F. Hose Clamps (2")
72593
G. Black Silicone Wrapped
Coupling (2" x 3")
72578
72929-B
A
B
D
F
Qty.
1
1
1
2
1
8
1
Page 2
STEP 1 - Locate the Vent Opening
a.
Select location on outside wall that vent will exit through.
b.
Check outside for proper clearances around vent cap. See installation instructions.
c.
Mark and cut 3-1/2" hole through both inside and outside walls, being sure to maintain level across both openings.
d.
Measure wall thickness. Mark and cut off both intake and exhaust pipes to 1/2" beyond outside wall.
e.
Secure collection box to wall. Wall anchors, not provided, may be required.
STEP 2 - Install Heater
a.
Select location on wall where heater will be installed.
b.
Using wall template supplied with heater, mark location for trim kit wall brackets.
c.
Attach brackets to wall (wall anchors, not provided, may be required) and back of heater.
Use screws provided on back of heater.
d.
Slide heater into position and secure brackets togehter. This should position back of heater 5" off wall.
e.
Select direction vent will exit trim kit. (Left, right or straight up).
f.
Before installing trim kit, remove knockout on this side.
STEP 3 - Install Vent
a.
Remove and discard the existing black flex tubing (P/N 72611) from air inlet. (Save hose clamp).
b.
Attach black flex tubing
Secure with a hose clamp
c.
SIide flocked tube
90 degree elbow (supplied with heater).
Secure with a hose clamp
d.
Attach support brackets
Postion support brackets within 8" from side of trim kit and end of pipe.
Secure flex tubing and flocked tube to brackets using hose clamps
e.
Attach center bracket
This will prevent the flex tube from touching the black flocked exhaust tube.
f.
Connect flex air intake tube and flocked exhaust tube to collection box using the black silicone coupling
Secure with a hose clamp
g.
Complete gas connection and attach trim kit to brackets.
h.
Follow lighting instructions.
SPECIAL NOTES:
a.
You may use up to three HEVK-5 Kits for a total
of 15' vent extension with two additional elbows.
DO NOT EXTEND VENT BEYOND 15 FEET OR
USE MORE THAN THREE TOTAL ELBOWS
(one elbow comes with the heater).
b.
To connect two vent kits together use the steel
coupling
A
c.
lf you are using one, two or three kits, after
installation is complete you will discard two (2)
hose clamps
d.
lf you need to make a 90 degree offset you will
need to order P/N HEEL-1 (90 degree Elbow Kit).
(Two offsets require two kits).
English Manual
English Manual
C
to air inlet.
F
.
B
through trim kit opening (knockout) and attach to P/N 72610 orange silicone
F
.
D
to wall. Wall anchors, not provided, may be required.
E
2-1/2' from pipe end and insert flex tube through bracket.
F
.
e.
If complete vent extension is horizontal, pipes may
be sloped down slightly to allow any condensation to
drain through the exhaust pipe to the outside.
DO NOT ALLOW TO DRAIN ONTO WALKWAY.
If any part of vent extension is vertical or local codes
do not allow draining of condensate to the outside,
. Secure with hose clamps
.
you must add P/N 18900 (Condensate Kit).
F
f)
For cosmetic purposes, the addition of the HEVK-5
Kit can be enclosed by adding an HEVE-5 Vent
and one steel coupling
.
F
A
Enclosure Kit.
To completely enclose the HEVK-5 Kit:
One HEVE-5 will be needed for each HEVK-5 used.
Page 3
F
.
G
.
72929-B
Publicité
