Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
American Sanders machine could result in injury to you or to other personnel; damage to the machine
or to other property could occur as well. You must have training in the operation of this machine
before using it. If your operator(s) cannot read this manual, have it explained fully before attempting
to operate this machine.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: Clarke
Form No. 70102B 1/07
Super E
Edger
Operator's Manual
Manual del operador
Manuel de l'utilisateur
®
, 2100 Highway 265, Springdale, Arkansas 72764
EN
English (2 - 10)
ES
Español (12-20)
FR
Français (22-30)
Printed in the U.S.A.
Publicité
Chapitres
Table des Matières
Manuels Connexes pour Clarke American Sanders Super E
Sommaire des Matières pour Clarke American Sanders Super E
- Page 1 Super E Edger Operator's Manual Manual del operador Manuel de l’utilisateur READ THIS BOOK English (2 - 10) Español (12-20) LEA ESTE MANUAL Français (22-30) LISEZ CE MANUEL This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel;...
-
Page 2: Table Des Matières
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. ® Operator's Manual (EN) - Super E Clarke American Sanders... -
Page 3: Operator Safety Instructions
• Hitting a nail while sanding can cause sparks and create an explosion or fire. Always use a hammer and punch to countersink all nails before sanding floors. Clarke ® American Sanders Operator's Manual (EN) - Super E - 3 -... - Page 4 Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs performed by unauthorized personnel will void your warranty. Servicing of this unit must always be referred to an authorized Clarke American Sanders distributor. CAUTION: Use of this equipment to move other objects or to climb on could result in injury or damage.
-
Page 5: Machine Specifications
13706A Extension 13" 5 inch 13 inches 3200 RPM 13708A Extension Picket 3 inch inches 5900 RPM 10019C Extension Picket 3 inch inches 5900 RPM w/¼ turn Clarke ® American Sanders Operator's Manual (EN) - Super E - 5 -... -
Page 6: Sanding Cuts And Sandpaper
120 grit For final sanding of certain conifers. 945605/500 150 grit For final sanding of certain conifers where a 945606/300 smooth surface is desired for surface roughening between coats of finish. ® Operator's Manual (EN) - Super E Clarke American Sanders... -
Page 7: Machine Set-Up
4. To empty the dust bag, unzip the disposal flap and force contents out by inverting the bag. NOTE: For best results, empty frequently. Follow all warnings posted in this manual and on the dust bag. Clarke ® American Sanders Operator's Manual (EN) - Super E - 7 -... -
Page 8: Operating Instructions
WARNING: Bodily injury could occur if power is applied to the machine with the control switch in the "ON" position. Always verify that the control switch is in the "OFF" position before connecting to the power cable. ® Operator's Manual (EN) - Super E Clarke American Sanders... -
Page 9: Adjustment Procedures
The design of the belt allows it to deliver the power with very little tenstion. The tension should be great enough to prevent slippage and wear. Excessive tension will only shorten bearing and belt life. Clarke ® American Sanders Operator's Manual (EN) - Super E - 9 -... -
Page 10: Routine Maintenance
Bearings To insure reliable performance, armature and pad driver bearings should be inspected for wear or damage after 1500 hours. If used heavily the bearings should be replaced seasonally. -10- ® Operator's Manual (EN) - Super E Clarke American Sanders... - Page 11 ENGLISH Clarke ® American Sanders Operator's Manual (EN) - Super E - 11 -...
- Page 12 Este manual contiene información importante acerca del uso y la seguridad de la máquina. Si no lee el manual antes de utilizar su máquina Clarke American Sanders o de intentar realizar los procedimientos de reparación o mantenimiento de la misma, usted o el resto del personal podrían sufrir lesiones;...
-
Page 13: Instrucciones De Seguridad Para El Operador
• Golpear un clavo cuando se lija puede causar chispas y crear una explosión o un incendio. Utilice siempre un martillo y perfore para avellanar todos los clavos antes de lijar los pisos. Clarke ® American Sanders Manual del operador (ES) - Super E - 13 -... - Page 14 El mantenimiento y las reparaciones de esta unidad siempre deben ser realizados por un distribuidor autorizado de Clarke American Sanders. PRECAUCIÓN: Si utiliza este equipo para desplazar otros objetos o para subirse al mismo se pueden producir lesiones o daños.
-
Page 15: Introducción Y Especificaciones De La Máquina
13708A Extensión para 3 pulgadas 47/8 pulgadas 5900 RPM balaustradas de peldaños 10019C Extensión para balaustradas de peldaños w/¼ turn 3 pulgadas 47/8 pulgadas 5900 RPM Clarke ® American Sanders Manual del operador (ES) - Super E - 15 -... -
Page 16: Cortes De Lija Y Papel De Lija
120 granos Para el lijado final de ciertas coniferas. 945605/500 Para lijado final de ciertas coníferas cuando se 945606/300 granos desea una superficie lisa para lograr aspereza entre las capas de acabado.. -16- Clarke ® American Sanders Manual del operador (ES) - Super E... -
Page 17: Instalación De La Máquina
NOTA: Para lograr los mejores resultados, vacíe frecuentemente. Siga todas las advertencias incluidas en el manual y en la bolsa de polvo. Clarke ® American Sanders Manual del operador (ES) - Super E - 17 -... -
Page 18: Operación De La Máquina
"ON" (Encendido). Verifique siempre que el interruptor de control se encuentre en posición "OFF" (Apagado) antes de enchufar el cable de alimentación. -18- Clarke ® American Sanders Manual del operador (ES) - Super E... -
Page 19: Procedimientos De Ajuste De La Lijadora
La tensión debería ser lo suficientemente importante como para prevenir deslizamiento y desgaste. La tensión excesiva solamente acortará la vida útil del cojinete y la correa. Clarke ® American Sanders Manual del operador (ES) - Super E - 19 -... -
Page 20: Mantenimiento De Rutina
1500 horas de funcionamiento, a los efectos de detectar desgaste o daños. Si la máquina se utiliza de forma intensiva, los cojinetes se deben cambiar estacionalmente. -20- Clarke ® American Sanders Manual del operador (ES) - Super E... - Page 21 ESPAÑOL Clarke ® American Sanders Manual del operador (ES) - Super E - 21 -...
-
Page 22: Contenu De Ce Manuel
La non-lecture de ce manuel avant d’utiliser ou d’entretenir votre machine Clarke American Sanders risque de provoquer un accident ou d’endommager la machine ou son environnement. Vous devez avoir été formé à l’utilisation de cette machine avant de l’utiliser. -
Page 23: Consignes De Securite Destinees A L'operateur
• En cours de ponçage, il est possible de provoquer une étincelle en heurtant un clou et ainsi, provoquer une explosion ou un incendie. Utilisez toujours un marteau et un poinçon pour fraisurer tous clous avant de sabler/poncer un plancher. ® Clarke American Sanders Manuel de l’utilisateur (FR) - Super E - 23 -... - Page 24 Les opérations de mainte- nance et les réparations effectuées par des techniciens non agréés annuleront votre garantie. Dirigez-vous toujours à un distributeur agréé Clarke American Sanders pour toutes réparations de cet appareil.
- Page 25 33 cm 3200 t/mn 13708A Piquet de rallonge 7,6 cm 12,4 cm 5900 t/mn 10019C Piquet de rallonge 7,6 cm 12,4 cm 5900 t/mn w/¼ turn ® Clarke American Sanders Manuel de l’utilisateur (FR) - Super E - 25 -...
-
Page 26: Ponçage Et Papier Abrasif
Pour le ponçage final de certains conifères. Grain 150 Pour le ponçage final de certains conifères 945606/300 lorsque l'on souhaite lisser une surface rugueuse entre les couches de finition. ® -26- Clarke American Sanders Manuel de l’utilisateur (FR) - Super E... -
Page 27: Préparation De L'appareil
NOTE: Pour obtenir les meilleurs résultats, vider fréquemment le sac. Respecter toutes les mises en garde indiquées dans le présent manuel et sur le sac à poussières. ® Clarke American Sanders Manuel de l’utilisateur (FR) - Super E - 27 -... -
Page 28: Assemblage De L'appareil
"ON" (marche). Toujours vérifier que le commutateur de commande se trouve en position "OFF" (arrêt) avant de brancher le câble d'alimentation. -28- Clarke ® American Sanders Manuel de l’utilisateur (FR) - Super E... -
Page 29: Réglage De La Ponceuse
La tension doit être suffisante pour éviter le patinage et l'usure. Une tension excessive ne fera qu'abréger la durée de vie des roulements et de la courroie. ® Clarke American Sanders Manuel de l’utilisateur (FR) - Super E - 29 -... -
Page 30: Entretien
S'ils sont très utilisés, les roulements devront être remplacés de manière saisonnière. -30- Clarke ® American Sanders Manuel de l’utilisateur (FR) - Super E... - Page 31 Super E Edger Section II Parts and Service Manual (70102B)
-
Page 32: Section Ii Parts And Service Manual Assemblydrawing #1
Model Super E Edger Drawing #1 12/06 Page 32 Clarke ® American Sanders Super E Operator's Manual... -
Page 33: Assembly Parts List #1
980643 Washer #10 40840A Suppressor 962289 Screw ¼-20 x ¾ Sc Hd * Certain Models Only NOTE: indicates a change has been made since the last publication of this manual. Clarke ® American Sanders Super E Operator's Manual Page 33... -
Page 34: Assembly Drawing #2
Model Super E Edger Drawing #2 1/03 Page 34 Clarke ® American Sanders Super E Operator's Manual... -
Page 35: Assembly Parts List #2
18, 24 (2 per assembly), 26, 27, 28, 29, 30 (3 per assemlby) 16528A Assembly Kick-Toe Extension w/5" Dia. Pad -Includes 4 (3 per assembly), 5, 6, 7, 8, 15, 17 (2 per assembly), 24 (2 per assembly), 26, 31, 32, 33 Clarke ® American Sanders Super E Operator's Manual Page 35... -
Page 36: Wiring Diagram
Model Super E Edger Wiring Diagram 1/96 Page 36 Clarke ® American Sanders Super E Operator's Manual... - Page 37 B.P. 44, 4 Place d’Ostwald F-67036 Strasbourg Cedex 2 +33 3 8828 8400 Clarke ® ALTO Nederland B.V. Clarke American Sanders Postbus 65 3370 AB Hardinxveld-Giessendam A.L. Cook The Netherlands Customer Service Headquarters and Factory +31 184 677 200 2100 Highway 265...
- Page 38 (b). Return the product to the nearest Clarke American Sanders repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke American Sanders will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product.