Additional Specific Safety Rules - Delta 23-198 Manuel D'utilisation

13. Form a habit of checking to see that all extra
equipment such as adjusting keys, wrenches,
scrap, stock, and cleaning rags are removed away
from the machine before turning on.
14. Keep safety guards in place at all times when the
machine is in use. If removed for maintenance
purposes, use extreme caution and replace the
guards immediately when maintenance is complete.
15. Make sure the tool is firmly secured to a stable work
15. Make sure the tool is firmly secured to a stable work
surface before use.
surface before use.
16. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced.
17. Provide for adequate space surrounding work area
and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of
scrap material, oil and grease.
19. Keep visitors a safe distance from the work area.
Keep children away.
20. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
21. Give your work undivided attention. Looking
around, carrying on a conversation and "horse-
play" are careless acts that can result in serious
injury.
22. Maintain a balanced stance at all times so that you
do not fall or lean against the tool or its moving
parts. Do not overreach or use excessive force to
perform any machine operation.

AddITIONAL SPECIFIC SAFETY RULES

Failure to follow these rules may result in serious personal injury.
1. dO NOT operate this machine until it is completely
assembled and installed according to the
instructions. A machine incorrectly assembled can
cause serious injury.
2. OBTAIN AdvICE from your supervisor, instructor, or
another qualified person if you are not thoroughly
familiar with the operation of this machine.
Knowledge is safety.
3. FOLLOw ALL wIRINg COdES and recommended
electrical connections to prevent shock or
electrocution.
4. ALwAYS USE ThE PROvIdEd BLOTTER and
wheel flanges to mount the grinding wheels on
the grinder shaft to prevent wheel damage or
accidental separation. Separation can result in
fragments flying off the wheel at high speeds.
5. USE ONLY whEELS suitable for the speed of the
machine. Unsuitable grinding wheels can come
apart, throwing fragments out at high speeds.
23. Use the right tool at the correct speed and feed
rate. Do not force a tool or attachment to do a job
for which it was not designed. The right tool will do
the job better and safer.
24. Use recommended accessories; improper
accessories may be hazardous.
25. Maintain machinery with care. Follow instructions
for lubricating and changing accessories.
26. Turn off the machine before cleaning. Use a brush
or compressed air to remove dust or debris — do
not use your hands.
27. Do not stand on the machine. Serious injury could
occur if the machine tips over.
28. Never leave the machine running unattended. Turn
the power off and do not leave the machine until it
comes to a complete stop.
29. At all times, hold the stock firmly.
30. Do not use this tool for other than it intended use. If
used for other purposes, DELTA
Corporation disclaims any real or implied warranty
and holds itself harmless for any injury or damage
which may result from that use.
Familiarize yourself with the following safety notices
used in this manual:
This means that if precautions are not heeded, it may
result in minor injury and/or possible machine damage.
This means that if precautions are not heeded, it may
result in serious injury or possibly even death.
6. USE ONLY whEELS that have a bore exactly
equal to the arbors of the machine. Never attempt
to machine an undersized wheel to fit an arbor.
Unsuitable grinding wheels can come apart,
throwing fragments out at high speeds.
7. dO NOT overtighten wheel nut.
8. dO NOT USE A whEEL ThAT vIBRATES. Dress
the grinding wheel, replace it, or replace the
bearings of the shaft. Unsuitable grinding wheels
can come apart, throwing fragments at high
speeds.
9. INSPECT whEELS before starting the machine
for cracks or fragments. REPLACE dAMAgEd
whEELS immediately. Parts of the wheel can be
thrown at high speeds causing serious injury.
10. AdJUST EYE ShIELdS close to the grinding
wheel, and re-adjust as the wheel wears down.
Flying sparks are dangerous and can cause fires or
explosions.
4
®
Power Equipment