Facom V.DGP150F Notice Originale page 7

• Where dust or fumes are created, the priority shall be to control them at the point of emission.
• All integral features or accessories for the collection, extraction or suppression of airborne dust or fumes
should be correctly used and maintained in accordance with the manufacturer's instructions.
• Select, maintain and replace the consumable/inserted tool as recommended in the instructions, to prevent
an unnecessary increase in dust or fumes.
• Working with certain materials creates emissions of dust and fumes, causing a potentially explosive
environment.
• Exposure to high noise levels can cause permanent, disabling hearing loss and other problems, such as tinni-
tus (ringing, buzzing, whistling or humming in the ears). Therefore, a risk assessment and the implementation
of appropriate controls for these hazards are essential.
• Appropriate controls to reduce the risk may include actions, such as damping materials, to prevent
workpieces from «ringing».
• Operate and maintain the grinder as recommended in the instructions handbook to prevent an unnecessary
increase in noise.
• Select, maintain and replace the consumable/inserted tool as recommended in the instructions handbook to
prevent an unnecessary increase in noise.
USING THE MACHINE
• Before using the machine, check that there is no dangerous interaction with the immediate environment
(explosive gas, inflammable or dangerous liquid, unknown piping, electric sheathing or cable, etc).
• Before connecting the machine to the air inlet, check the trigger is not blocked in the on position by an
obstacle and no adjustment or assembly tool is still in position.
• Check the machine is connected to the network by a quick disconnect joint and that an air braker valve
is close by to shut the air down immediately in the event of blockage, breakage or any other incident.
• Keep hands, loose clothing and long hair away from rotating end of machine.
• Anticipate and be alert for sudden changes in motion during start up and operation of any power
machine.
• Ensure that the unit on which the work is being carried out is immobilised.
• In the event of blockage, release the trigger and disconnect the machine from the compressed air
network.
• Be certain that its maximum safe operating speed does not exceed the nameplate speed on the
grinder.
• Always turn off the air supply, drain hose of air pressure and detach tool from air supply before
installing, removing, or adjusting any part or accessory on this tool, or before performing any
maintenance on this tool.
• Bonded abrasive mounted point grinding wheels, rotary files and carbide burrs can be mounted provi-
ding their speed rating exceed the speed of the grinder. The shank size of the mounted accessory must
match the collet size fitted in the grinder. Insert the shank of the mounted point as far as possible into the
collet and tighten the nut using the supplied wrenches. Minimum shank gripping length must be 10mm.
MAINTENANCE
Your FACOM STRAIGHT HEAD PENCIL DIE GRINDER has been designed to operate
over a long period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Lubrication
Every eight hours' operation, if a lubricator is not used on the compressed air network,
inject 1/2 to 1cm through the machine's inlet connection.
3
Do not use damaged, frayed or deteriorated air hoses
and fittings.
The pneumatic machine can vibrate in use. Vibration, repetitive
motions or uncomfortable positions may be harmful to your hands
and arms. Stop using any machine if discomfort, tingling feeling
or pain occurs.
Seek medical advice before resuming use.
Do not carry the machine by the hose.
Keep body stance balanced and firm. Do not overreach when
operating this machine.
Do not use the machine under the influence of drugs, alcohol,
medication or if you are tired.
NU-V.DGP150F_0716.indd 7
• Wear warm clothing whenever working in cold conditions and keep your hands warm and dry.
• Operate and maintain the grinder as recommended in the instructions handbook to prevent an unnecessary
increase in vibration levels.
• Do not allow the inserted tool to chatter on the workpiece as this is likely to cause a substantial increase
in vibration.
• Select, maintain and replace the consumable/inserted tool as recommended in the instructions handbook to
prevent an unnecessary increase in vibration levels.
• Hold the tool with a light but safe grip, taking account of the required hand reaction forces because the risk
arising from vibration is generally greater where the grip force is higher.
• Use blotters where they are provided with the bonded abrasive product.
• Never direct air at yourself or anyone else.
• Whipping hoses can cause severe injury. Always check for damaged or loose hoses and fittings.
• Whenever universal twist couplings (claw couplings) are used, lock-pins shall be installed and whipcheck
safety cables shall be used to safeguard against possible hose-to-tool and hose-to-hose connection failure.
• After mounting a new point, start the grinder under bench and run for a few seconds. If the grinder
starts to vibrate when first fitting a mounted point or during operation, immediately remove from
service. If the grinder is dropped, replace bonded abrasive mounted point grinding wheel, rotary file
or carbide burr.
• When using the grinder, be careful not to exert excessive force which could be hazardous and cause
mounted spindle to bend or break.
NOTE : During operation, safety goggles must always be worn to guard against flying rust and chips
(users & bystanders).
If the air supply, hoses, and connectors are in order, and the tool is still not functionning properly, take
tool to your nearest FACOM Authorized Service center.
• Use accessories recommended by FACOM.
• The use of other than genuine FACOM replacement parts may result in safety hazards, decreased
machine performance, and increased maintenance, and cancel all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest FACOM Authorized
Servicenter.
Cleaning
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the plastic materials used in these
parts. Use a cloth dampened only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
WARNING
Use protective equipment such as glasses, gloves, safety shoes as well
as acoustic protection.
Remain vigilant, use common sense and pay attention when using
the machine.
Always turn off the air supply and disconnect the airsupply hose
before installing, removing or adjusting any accessory on this
machine, or before performing any maintenance on this machine.
When working with certain materials, exposure to dust may be
dangerous for health.
Get information on the composition of the material you are working
on and use suitable protective equipment. If in doubt, use as much
protection as possible.
29/07/2016 11:10:31