BTI A18 DSS-2 1/4 Notice Originale page 15

EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant provisions
of the directives 2011/65/EU (RoHs), 2014/30/EU, 2006/42/EC and
the following harmonized standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-2:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 50581:2012
Ingelfi ngen, 2018-01-30
Andreas Krebs
Geschäftsführung
Authorized to compile the technical fi le
BTI Befestigungstechnik GmbH & Co. KG
Salzstraße 51
D-74653 Ingelfi ngen
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be
fully charged.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate for
about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the
battery could become to high. If this happens, the battery will shut
445 253 - BTI-A18DSS-2_14.indd 15 445 253 - BTI-A18DSS-2_14.indd 15
Stefan Haug
Anwendungstechnik
down.
Place the battery on the charger to charge and reset it.
INTENANCE
Use only BTI accessories and spare parts. Components whose
replacement has not been described, can be exchanged at the BTI
after sales service. (BTI Befestigungstechnik GmbH & Co. KG ·
After Sales Service · Salt Road 51 · 74653 Ingelfi ngen · Tel 07940
/ 141-870, -872, -873 or -886 · Fax 07940 / 141-875)
If needed, an exploded view of the tool can be ordered. Please
state the ten-digit No. as well as the machine type printed on the
label and download the drawing at BTI Homepage www.bti.de >
Service > Explosionszeichnungen und Ersatzteillisten > BTI >
Akku-Geräte or order directly at BTI Befestigungstechnik GmbH &
Co. KG, After Sales Service, Salzstraße 51, 74653 Ingelfi ngen.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
GUARANTEE AND GUARANTEE SERVICE
Each tool, spare part or accessory is consistently checked
before being dispatched from the manufacturing plant. If,
despite this fact, there are any defects, please send the
item directly to our Client Services Headquarters or to the
nearest service repair shop of the firm BTI.
BTI after sales service can be reached at the following
contact information: BTI Befestigungstechnik GmbH &
Co. KG · After Sales Service · Salz Straße 51 · 74653
Ingelfi ngen · Tel 07940/141 - 874 · Fax 07940 / 141-9874
The warranty period of 36 months for tools and 12 months
for batteries and chargers starts on the date of purchase
which must be verifi ed using the original receipt. During
the guarantee period the producer guarantees:
• free removal of possible defects;
• free replacement of all damaged parts;
• free professional servicing.
The requirement for this is that the problem is a material
and/or manufacturing fault. Defects or faults caused by
incorrect treatment or excessive force are not covered
by the warranty. Furthermore, only original accessory
parts may be used, which BTI has expressly identifi ed as
suitable for the operation with BTI machines.
You can fi nd out the location of your nearest customer
service workshop in the address list at the back of this
document.
15 ENGLISH
30.01.2018 13:04:28 30.01.2018 13:04:28