Technical Data; Impact Driver Safety Warnings; Additional Safety And Working Instructions; Specified Conditions Of Use - BTI A18 DSS-2 1/4 Notice Originale

TECHNICAL DATA

CORDLESS IMPACT SCREWDRIVER
Code .............................................................................................
Tool reception ...............................................................................
No-load speed, 1st gear ...............................................................
No-load speed, 2nd gear ..............................................................
Impact range, 1st gear..................................................................
Impact range, 2nd gear ................................................................
Torque max ...................................................................................
Max. diameter bolt / nut ................................................................
Battery voltage..............................................................................
Weight according EPTA-Procedure 01/2003 (1.5/2.0 Ah) ............
Weight according EPTA-Procedure 01/2003 (3.0/4.0/5.0 Ah) ......
Weight according EPTA-Procedure 01/2003 (9,0 Ah) ..................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .............................
Sound power level (Uncertainty K=3dB(A)) ..................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Vibration emission value a
h
Impact tightening of fasteners of the maximum capacity of the tool .
Uncertainty K= ...........................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with
diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running
but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

IMPACT DRIVER SAFETY WARNINGS

Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a „live" wire may make
exposed metal parts of the power tool „live" and could give the
operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
ENGLISH
445 253 - BTI-A18DSS-2_14.indd 14 445 253 - BTI-A18DSS-2_14.indd 14
A18 DSS-2 1/4"
A18 DSS-2 1/4" 02 00001- 99999
.......................... 1/4" (6,35 mm)
..................... 0-2000 min -1
..................... 0-2750 min
-1
..................... 0-2450 min
-1
..................... 0-3450 min -1
...........................180 Nm
..........................M14
.............................18 V
............................1,4 kg
............................1,7 kg
............................2,1 kg
..........................93,8 dB (A)
........................104,8 dB (A)
..........................12,3 m/s
2
..........................2,77 m/s
2
Sawdust and splinters must not be removed while the machine is
running.
When working in walls ceiling, or fl oor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. BTI off er to retrieve old batteries to protect our
environment; please ask your sales representative or our service
line at 07940 / 141-141.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System BTI chargers for charging System BTI battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fl uid or al-low a fl uid to fl ow inside them.
Corrosive or conductive fl uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.

SPECIFIED CONDITIONS OF USE

The cordless impact wrench can be used to tighten and loosen
nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.
14
30.01.2018 13:04:28 30.01.2018 13:04:28