Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
CONVERGE (cont.)
Note:
After selecting, press VOL
DEFAULT feature.
CONVERGE.
CONVERGENCE ADJ.
RESET TO DEFAULT
PRESS ACTION TO RETURN
Procedure
•
After pressing VOL
will be displayed.
•
Then use the navigation buttons on the remote control
to align the horizontal and vertical green lines on screen
with the cabinet reference marks on top center and left
center of cabinet, as shown below.
Reference Marks
PRESS CH AND VOL KEY TO
ALIGN GREEN LINES TO THE
CENTER MARK ON THE CABINET
Front of cabinet
PRESS ACTION TO CONTINUE
ACTION
•
Press
to display red center correction screen.
•
Use the navigation buttons on the remote control to align
the red cross with the white cross pattern at the center of
the screen.
Note:
To prevent picture tube damage, do not leave
test pattern on for an extended period of time.
•
Then press "0" on the remote control keypad to display
the BLUE center correction screen. Repeat procedure
for adjusting blue. If needed press "0" again to return to
RED correction screen.
Note:
An adjusted cross pattern appears white with a minimum
of color protrusion.
IF RED IS PROTRUDING FROM
CENTER CROSS, PRESS CH AND
VOL KEY TO CORRECT
UP
LEFT
RIGHT
DOWN
PRESS 0 TO ADJUST BLUE
PRESS ACTION TO CONTINUE
NINE POINT CONVERGENCE CORRECTION
Note:
Remote Control must be in TV mode.
Procedure
ACTION
•
Press
to display red correction screen.
•
Press the 1 through 9 keypad buttons on the remote
control to select the desired convergence position.
•
Use the navigation buttons to align the RED cross with
the white cross pattern.
Note:
An adjusted cross pattern appears white with a minimum
of color protrusion.
to activate RESET TO
SET UP
the align Green to Center screen
UP
RIGHT
LEFT
DOWN
IF BLUE IS PROTRUDING FROM
CENTER CROSS, PRESS CH AND
VOL KEY TO CORRECT
Press
UP
"0"
LEFT
RIGHT
DOWN
PRESS 0 TO ADJUST BLUE
PRESS ACTION TO CONTINUE
1
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
4
CORRECTING RED
PRESS 0 TO ADJUST BLUE
PRESS ACTION TO EXIT
PRESS ACTION TO EXIT
7
•
Press "0" on the remote control keypad to display the
BLUE correction screen, then repeat procedure.
2
3
1
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
4
6
CORRECTING RED
PRESS 0 TO ADJUST BLUE
PRESS ACTION TO EXIT
PRESS ACTION TO EXIT
9
8
7
ACTION
•
To exit press
ZOOM ADJ.
This feature lets you adjust the size of the zoom picture and
position it vertically.
SIZE
V-POSITION
NORMAL
ZOOM ADJ.
PRESS ACTION TO RETURN
Note:
This feature is only selectable while in Zoom mode.
Press the ASPECT button on the remote control for
selecting Zoom mode.
OTHER ADJ.
Highlight OTHER ADJ. and press VOL
menu field.
Note:
While sub sub-menu features are highlighted, press
VOL
to adjust or activate.
MODE
AUTO PROGRAM
MANUAL PROGRAM
AUTO POWER ON
OTHER ADJ
.
CHAN BANNER
IMAGE SHIFT
PRESS ACTION TO RETURN
•
MODE - To select TV (antenna) or CABLE mode
depending on the signal source.
•
AUTO PROGRAM - To automatically program all
channels received through the RF input.
•
MANUAL PROGRAM - To manually add or delete
channels.
•
AUTO POWER ON - Select SET to power up the TV at
the same time as the Cable box or other components or
select OFF.
•
CHAN BANNER - Select ON to display onscreen banner
when changing channels.
•
IMAGE SHIFT - Selecting ON is recommended for this
feature to prevent image retention on screen.
I
M
O
CON
ENUS
PERATION
2
3
6
9
8
2
1
PRESS # KEY TO SELECT POS.
Press
PRESS CH AND VOL KEY TO CORR.
4
"0"
CORRECTING BLUE
PRESS 0 TO ADJUST RED
PRESS ACTION TO EXIT
PRESS ACTION TO EXIT
8
7
repeatedly, then press CH
SET UP
4
0
SET
to enter sub sub-
SET UP
CABLE
OFF
ON
ON
3
6
9
.
25
Publicité
Chapitres
Table des Matières
Dépannage
