Programming The Remote Control; Programming Without A Code; Component Codes - Panasonic PT-53TW54 Manuel D'utilisation

Programming The Remote Control

The Universal Remote Control can be programmed to
operate many manufacturers' components using the
component function buttons for VCR, DVD, AUX, RCVR,
TV, DTV CABLE or DBS. Follow the procedures for
programming your Remote Control with or without a code
for the component.
Default Modes for Remote Control
Device Operates
TV
TV (Panasonic Only)
DTV-STB
DTV (Panasonic Only)
CABLE
CABLE (Preset)
DBS
DBS (Preset)
VCR
VCR (Preset)
DVD/CD
DVD and CD (Preset)
Personal Video Recorders,
AUX
Tape and VCR2
RCVR
Audio receiver (Preset)
Note: Determine the manufacturer of the component and look
in the table for the code (found on page 16 and 17).
Procedure
1. Confirm that the external component is plugged in and
operating.
2. Turn the component off.
ACTION
3. Press and
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press appropriate component button on the Remote
VCR, DVD (CD), AUX (VCR2 or TAPE),
Control:
RCVR, DTV, CABLE or DBS.
will illuminate steadily and all others will go out.
5. Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons). The component
button will blink twice.
6. Press the Remote Control
component. If the procedure was successful, the
component will turn on and the component key will blink
twice and then go out.
Note: If the component does not operate with the Remote
Control, repeat the steps 3 through 6 using another code
(some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30
seconds, the programming will fail.
Default
Panasonic TV Code
Panasonic DTV Code
Panasonic CABLE
Code
Panasonic DBS Code
Panasonic VCR Codes
Panasonic DVD Codes
Panasonic Personal
Video Recorder Code
Panasonic RCVR code
together for at least 5
POWER
The component button
to test the
POWER
R
EMOTE

Programming Without A Code

This procedure searches all codes and is called the
"sequence method."
1. Confirm that the external component is plugged in and
on.
2. Turn the component off.
ACTION
3. Press and
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press the appropriate component button on the Remote
Control. The component button will illuminate steadily
and all others will go out.
5. Press the button to set the remote control to the
POWER
step and set mode.
6. Point the remote control towards the component.
7. Press VOL (the mode key will blink three times), then
press the Remote Control
component. Continue this process until the proper code
is found. If the procedure was successful, the component
will turn on.
Note: Each time you press the VOL
component key blinks twice before pressing the POWER
button.
8. Once the device responds, press
code. The mode (component) button will blink twice.
Note: It may take many attempts before the correct code
is found. If you miss a code, press
the button to test the component.
POWER

Component Codes

The Universal Remote Control is capable of operating
many component brands after entering a code. Some
components may not operate because the codes are not
available due to limited memory. The Universal Remote
Control does not control all features found in each model.
Write the code numbers from tables in this space.
This will serve as a reference if you need to program
your Remote Control.
VCR DVD
AUX (VCR2) AUX (TAPE)
DTV CABLE
C O
ONTROL PERATION
together, for at least 5
POWER
button to test the
POWER
button, make sure that the
ACTION
to store the
VOL, then press
DVD (CD)
RECEIVER
DBS
15